Home › Vehicle Exterior › BODY WELD POINT › RADIATOR SUPPORT
BM3210E _01 Vehicle Exterior _050433 BODY WELD POINT _0251808 RADIATOR SUPPORT F

BODY WELD POINT  RADIATOR SUPPORT  ASSEMBLY REPLACEMENT  


K131442

REMOVAL


Symbol Meaning
K108818

Remove Weld Points

K131480

K131481C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH Side - -


K131482C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH Side - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

For vehicles with a millimeter wave radar sensor, the bolts and bolt area must not be damaged. (See the body dimensions)

K131483C01
2,5.167 2.917,5.417 0.917,0.25 0.833,0.333 1.75,0.583 0.917,0.25 4.083,4.833 5,5.083 0.917,0.25 1.5,4.5 2.417,4.75 0.917,0.25 2.917,0.75 3.833,1 0.917,0.25 4,0.333 4.917,0.583 0.917,0.25 5.25,1.25 6.167,1.5 0.917,0.25 3.417,2.75 3.75,2.5 3.75,2.5 3.917,2.5 false 3.167,3.854 3.333,4.333 3.333,4.333 3.5,4.333 false 4.75,3.906 4.917,4.167 4.917,4.167 5.083,4.167 false 2.094,3.5 1.833,3.833 1.833,3.833 1.667,3.833 false 4.552,4.833 4.552,4.51 false 2.229,4.5 2.229,4.177 false 1.75,0.531 2.25,0.531 false 2.469,0.917 2.917,0.917 false 4.458,0.583 4.458,1 false 4.646,1.417 5.25,1.417 false 2.5,5.167 2.5,4.917 false 3.938,2.417 4.25,2.573 0.313,0.156 10 false *1 3.521,4.25 3.833,4.406 0.313,0.156 10 false *2 5.104,4.083 5.417,4.24 0.313,0.156 10 false *3 1.521,3.75 1.833,3.906 0.313,0.156 10 false *3 0.917,0.385 2.906,0.583 1.99,0.198 10 false 12.5 (127, 9) 4.167,4.885 6,5.083 1.833,0.198 10 false 30 (306, 22) 1.583,4.552 3.417,4.75 1.833,0.198 10 false 30 (306, 22) 3,0.802 4.99,1 1.99,0.198 10 false 12.5 (127, 9) 4.083,0.385 6.073,0.583 1.99,0.198 10 false 12.5 (127, 9) 5.333,1.302 6.323,1.5 0.99,0.198 10 false 12.5 (127, 9) 2.083,5.219 4.073,5.417 1.99,0.198 10 false 12.5 (127, 9)
*1 RADIATOR SUPPORT SUB-ASSEMBLY UPPER *2 RADIATOR SUPPORT SUB-ASSEMBLY LOWER
*3 RADIATOR SUPPORT SUB-ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -


K131484C01
3.25,1.323 3.667,0.833 3.667,0.833 3.833,0.833 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.854,0.75 4.167,0.906 0.313,0.156 10 false *1
*A LH Side - -
*1 RADIATOR SUPPORT UPPER - -


K131485C01
3.5,0.917 3.667,0.917 3.667,0.917 3.99,1.313 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.354,0.833 3.667,0.99 0.313,0.156 10 false *1
*A RH Side - -
*1 RADIATOR SUPPORT UPPER - -



d.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


e.

Measure the dimensions before installing the headlights.

K131486N01
3.375,3.625 3.531,3.823 0.156,0.198 10 true B 3.177,3.969 3.333,4.167 0.156,0.198 10 true C 2.75,2.333 2.906,2.531 0.156,0.198 10 true D 4.25,3.135 4.406,3.333 0.156,0.198 10 true E 2.927,2.969 3.083,3.167 0.156,0.198 10 true F 3.75,2.719 3.906,2.917 0.156,0.198 10 true A

Reference Value:
Area Measurement Area Measurement
A 1376 mm (54.17 in.) B 1043 mm (41.06 in.)
C 964 mm (37.95 in.) D 730 mm (28.74 in.)
E 865 mm (34.06 in.) F 922 mm (36.30 in.)



f.

Position of marks for body repair

K131650C01
5.917,1.542 6.083,0.833 6.083,0.833 6.25,0.833 false 1.167,0.917 1.333,0.917 1.333,0.917 1.667,1.917 false 1.583,3.333 1.75,3.333 1.75,3.333 2,2.833 false 4.833,3.083 5,3.083 5,3.083 5.25,2.583 false 1.438,3.25 1.75,3.406 0.313,0.156 10 false *1 4.688,3 5,3.156 0.313,0.156 10 false *2 1.021,0.833 1.333,0.99 0.313,0.156 10 false *a 6.271,0.75 6.583,0.906 0.313,0.156 10 false *a
*1 FRONT BUMPER STAY SUB-ASSEMBLY *2 RADIATOR GRILLE MOUNTING BRACKET
*a MARK FOR BODY REPAIR - -



g.

Weld the front bumper stay sub-assembly to the radiator upper support.

HINT:

The values shown here are reference values. Use for temporary installation.


K131651C01
2.417,2.75 2.583,2.75 2.583,2.75 2.844,2.333 false 2.167,1.583 2.333,1.583 2.333,1.583 2.583,1.167 false 2.021,1.5 2.333,1.656 0.313,0.156 10 false *1 4.271,3 4.583,3.156 0.313,0.156 10 false *a 2.271,2.667 2.583,2.823 0.313,0.156 10 false *2
*1 RADIATOR UPPER SUPPORT *2 FRONT BUMPER STAY SUB-ASSEMBLY
*a 29 mm (1.14 in.) - -


K131652


h.

Weld the radiator grille mounting bracket to the front bumper stay sub-assembly.

HINT:

Determine the vertical and horizontal orientation of the radiator grille mounting bracket by using the marks for body repair.


K131653C01
3,0.979 2.917,0.5 2.917,0.5 3.083,0.5 false 5.115,3.771 5.583,3.083 5.583,3.083 5.75,3.083 false 5.26,3.958 5.583,3.083 false 2.583,2.167 2.75,2.167 2.75,2.167 3.052,1.833 false 2.438,2.083 2.75,2.24 0.313,0.156 10 false *1 5.771,3 6.083,3.156 0.313,0.156 10 false *a 3.104,0.417 3.417,0.573 0.313,0.156 10 false *2
*1 FRONT BUMPER STAY SUB-ASSEMBLY *2 RADIATOR GRILLE MOUNTING BRACKET
*a MARK FOR BODY REPAIR - -