Home › Vehicle Exterior › BODY WELD POINT › CENTER BODY PILLAR
BM3210E _01 Vehicle Exterior _050433 BODY WELD POINT _0251818 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K131454

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Be careful when cutting as foamed sealing material is located near the cutting position.

K131655C01
0,0 0,0 false
K108840

Foamed Sealing Material - -


K131539C01
3.469,0.458 3.781,0.615 0.313,0.156 10 false *a
*a 20 mm (0.79 in.) - -


K131540C01
1.76,4.083 2.073,4.24 0.313,0.156 10 false *a
*a 190 mm (7.48 in.) - -
K111603

Laser Screw Welding - -


K131541

K131542C01
3.76,0.865 4.073,1.021 0.313,0.156 10 false *a
*a 25 mm (0.98 in.) - -
K111603

Laser Screw Welding - -



c.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Weld the center body pillar reinforce sub-assembly lower to the vehicle side.

K131543C01
3.573,1.927 3.833,1.417 3.833,1.417 4,1.417 false 4.021,1.333 4.333,1.49 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
K111603

Laser Screw Welding - -



d.

Weld the center body pillar reinforcement sub-assembly to the vehicle side.

K131544C01
3.083,3.083 3.25,3.083 3.25,3.083 3.75,3.75 false 2.938,3 3.25,3.156 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




e.

Be careful when welding as foamed sealing material is located near the area that is cut and joined together.

K131655C01
0,0 0,0 false
K108840

Foamed Sealing Material - -



f.

Weld the center body pillar outer to the vehicle side.

K131545C01
3.688,4.031 3.333,3.417 3.333,3.417 3.167,3.417 false 3.021,3.333 3.333,3.49 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR OUTER - -
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding more than 3 panels together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.