Home › Vehicle Exterior › BODY WELD POINT › ROCKER PANEL
BM3210E _01 Vehicle Exterior _050433 BODY WELD POINT _0251822 ROCKER PANEL F

BODY WELD POINT  ROCKER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K131458

With the front body pillar cut and join replacement sections (pattern 1) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Carefully cut the center body pillar reinforcement sub-assembly so not to damage A.

K131557C01
3.083,6.25 3.25,6.25 3.25,6.25 3.667,6.583 false 2.583,7 2.75,7 2.75,7 2.917,7.198 false 2.438,6.917 2.75,7.073 0.313,0.156 10 false *1 5.417,4.083 5.729,4.24 0.313,0.156 10 false *a 4.521,6.792 4.833,6.948 0.313,0.156 10 false *b 2.938,6.167 3.094,6.365 0.156,0.198 10 false A
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a 60 mm (2.36 in.) *b 120 mm (4.72 in.)
K111603

Laser Screw Welding - -


K131558

K131559C01
0,0 0,0 false
K111603

Laser Screw Welding - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K131662C01
2.167,2.917 2.333,2.917 2.333,2.917 2.625,3.25 false 2.021,2.833 2.333,2.99 0.313,0.156 10 false *1 4.177,2.854 4.49,3.01 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a 120 mm (4.72 in.) - -



d.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer and center body pillar reinforcement sub-assembly with the standard number of welding points.

K131663C01
4.333,1.5 4.667,1.167 4.667,1.167 4.833,1.167 false 2.917,2.667 3.083,2.667 3.083,2.667 3.417,2.313 false 2.771,2.583 3.083,2.74 0.313,0.156 10 false *1 4.854,1.083 5.167,1.24 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




e.

Weld the rocker reinforce sub-assembly outer and center body pillar reinforcement sub-assembly to the vehicle side.

K131664C01
5.333,4.958 5.417,4.667 5.417,4.667 5.583,4.667 false 2,6.083 1.833,6.083 1.833,6.083 2.146,5.594 false 2.021,6 2.333,6.156 0.313,0.156 10 false *1 5.604,4.583 5.917,4.74 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K131665C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Weld the center body pillar outer to the vehicle side.

K131562C01
1.667,4.5 1.833,4.5 1.833,4.5 2.188,4.99 false 1.521,4.417 1.833,4.573 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR OUTER - -
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding more than 3 panels together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.