Home › Vehicle Exterior › BODY WELD POINT › REAR FLOOR UPPER CENTER CROSSMEMBER
BM3210E _01 Vehicle Exterior _050433 BODY WELD POINT _0251830 REAR FLOOR UPPER CENTER CROSSMEMBER F

BODY WELD POINT  REAR FLOOR UPPER CENTER CROSSMEMBER  ASSEMBLY REPLACEMENT  


K131469

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.

a.

Remove the A and B.

K131623C01
0.167,3.25 7,7.667 6.833,4.417 3.583,7.667 3.583,3.25 false 4.833,1.25 5.5,0.667 5.5,0.667 5.667,0.667 false 2.333,1.25 1.667,0.667 1.667,0.667 1.5,0.667 false 0.333,3.417 0.646,3.573 0.313,0.156 10 false *A 3.75,3.417 4.063,3.573 0.313,0.156 10 false *B 1.354,0.583 1.51,0.781 0.156,0.198 10 false A 5.698,0.583 5.854,0.781 0.156,0.198 10 false B
*A LH Side *B RH Side
K111603

Laser Screw Welding - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K131626C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the A.

K131624N01
4.75,1.75 5.583,1.083 5.583,1.083 5.75,1.083 false 5.771,1 5.927,1.198 0.156,0.198 10 false A



INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Remove A and B from the new parts.

K131625C01
0.167,2.167 6.917,4.583 6.75,2.417 3.583,4.583 3.583,2.167 false 4.75,0.927 5.167,0.583 5.167,0.583 5.333,0.583 false 2.417,0.927 2,0.583 2,0.583 1.833,0.583 false 3.667,1.583 3.5,1.583 3.5,1.583 3.083,1.208 false 0.333,2.333 0.646,2.49 0.313,0.156 10 false *A 3.75,2.333 4.063,2.49 0.313,0.156 10 false *B 3.688,1.5 4,1.656 0.313,0.156 10 false *1 1.688,0.5 1.844,0.698 0.156,0.198 10 false A 5.354,0.5 5.51,0.698 0.156,0.198 10 false B
*A LH Side *B RH Side
*1 CENTER FLOOR CROSS MEMBER NO. 2 - -



c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K131626C01
0,0 0,0 false
K108837

Adhesive - -



d.

Weld the A to the vehicle side.

K131627N01
4.75,1.75 5.5,1.25 5.5,1.25 5.667,1.25 false 5.698,1.167 5.854,1.365 0.156,0.198 10 false A


e.

Weld the A and B to the vehicle side.

K131628C01
0.167,3.25 7,7.667 6.833,4.417 3.583,7.667 3.583,3.25 false 2.333,1.24 1.667,0.75 1.667,0.75 1.5,0.75 false 4.833,1.24 5.5,0.75 5.5,0.75 5.667,0.75 false 0.333,3.417 0.646,3.573 0.313,0.156 10 false *A 3.75,3.417 4.063,3.573 0.313,0.156 10 false *B 3.083,4.219 3.396,4.375 0.313,0.156 10 false *a 3.75,4.219 4.063,4.375 0.313,0.156 10 false *a 1.354,0.667 1.51,0.865 0.156,0.198 10 false A 5.688,0.667 5.844,0.865 0.156,0.198 10 false B
*A LH Side *B RH Side
*a 27 mm (1.06 in.) - -
K111603

Laser Screw Welding - -



f.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.