Home › Vehicle Exterior › BODY WELD POINT › NAME PLATE
BM3210E _01 Vehicle Exterior _050433 BODY WELD POINT _0251836 NAME PLATE F

BODY WELD POINT  NAME PLATE  ATTACHMENT POSITION  


1.

Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.

HINT:

Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.


2.

Wipe off the remaining double-sided tape using a clean cloth or equivalent.

NOTICE:

If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.


3.

After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.

HINT:

The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.



B435972C01
0.198,4.813 3.042,6.417 2.844,1.604 4.052,4.823 6.938,6.365 2.885,1.542 1.906,1.354 2.792,1.354 true 4.365,1.344 5.25,1.344 true 4.365,1.656 5.25,1.656 true 3.667,1.281 4.99,0.594 4.99,0.594 5.24,0.594 true 3.604,4.427 3.604,4.281 false 5.51,6.51 5.51,6.365 false 1.646,6.563 1.646,6.417 false 5.625,7.219 5.625,7.073 false 3.615,4.458 4.094,4.677 0.479,0.219 10 false ● *1 5.635,7.26 6.115,7.479 0.479,0.219 10 false ● *2 5.521,6.521 5.979,6.729 0.458,0.208 10 false ● *3 1.646,6.625 2.219,6.885 0.573,0.26 10 false ● *4 1.552,1.292 2.01,1.49 0.458,0.198 10 false <A> 5.313,0.531 5.771,0.729 0.458,0.198 10 false <B> 5.323,1.271 5.781,1.469 0.458,0.198 10 false <C> 5.333,1.583 5.792,1.781 0.458,0.198 10 false <D> 1.25,6.635 1.708,6.833 0.458,0.198 10 false <A> 3.26,4.469 3.719,4.667 0.458,0.198 10 false <B> 5.115,6.531 5.573,6.729 0.458,0.198 10 false <C> 5.271,7.281 5.729,7.479 0.458,0.198 10 false <D>
*1 BACK DOOR ORNAMENT SUB-ASSEMBLY *2 NO. 1 BACK DOOR NAME PLATE
*3 NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE *4 NO. 3 LUGGAGE COMPARTMENT DOOR PLATE
● Non-reusable part - -


B435973C01
2.01,3.292 2.01,3.073 false 5.354,3.333 5.354,3.115 false 1.854,3.344 2.313,3.573 0.458,0.229 10 false ● *1 5.219,3.354 5.677,3.583 0.458,0.229 10 false ● *1 0.25,0.188 0.625,0.427 0.375,0.24 12 false *A 4.198,0.167 4.573,0.406 0.375,0.24 12 false *B
*A for LH Side *B for RH Side
*1 SIDE PANEL EMBLEM - -
● Non-reusable part - -


SIDE PANEL EMBLEM


a.

for LH Side:

B435987N01
0.927,1.583 1.083,1.781 0.156,0.198 10 false A 2.313,1.063 2.469,1.26 0.156,0.198 10 true B

Standard Measurement:
Area Measurement Area Measurement
A 133.9 mm (5.27 in.) B 95.5 mm (3.76 in.)



b.

for RH Side:

B435988N01
4.448,1.052 4.604,1.25 0.156,0.198 10 true A 5.865,1.594 6.063,1.823 0.198,0.229 10 false B

Standard Measurement:
Area Measurement Area Measurement
A 95.1 mm (3.74 in.) B 136.2 mm (5.36 in.)




BACK DOOR ORNAMENT SUB-ASSEMBLY


B435981


NO. 3 LUGGAGE COMPARTMENT DOOR PLATE


a.

for PRIUS Plate:

B436132C01
1.771,1.625 1.354,1.188 true 3.25,1.625 2.906,1.354 true 0.781,1.896 0.625,1.896 true 1.156,1.052 1.469,1.208 0.313,0.156 10 false *a 0.438,1.802 0.75,1.958 0.313,0.156 10 false *b 2.719,1.24 3.031,1.396 0.313,0.156 10 false *a 0.177,1.198 0.333,1.396 0.156,0.198 10 false A 1.24,0.531 1.427,0.719 0.188,0.188 10 false B 1.875,0.188 2.125,0.417 0.25,0.229 10 false C 3.677,1.188 3.927,1.406 0.25,0.219 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 105.6 mm (4.16 in.) B 100.9 mm (3.97 in.)
C 235.6 mm (9.28 in.) D 97.9 mm (3.85 in.)



b.

for TOYOTA Plate:

B435984C01
1.344,1.344 1.708,1.635 true 2.458,1.333 2.823,1.625 true 0.594,1.885 0.771,1.885 true 1.156,1.24 1.469,1.396 0.313,0.156 10 false *a 0.385,1.792 0.698,1.948 0.313,0.156 10 false *b 2.271,1.208 2.583,1.365 0.313,0.156 10 false *a 0.135,1.219 0.333,1.469 0.198,0.25 10 false A 1.031,0.552 1.229,0.802 0.198,0.25 10 false B 1.656,0.219 1.854,0.469 0.198,0.25 10 false C 3.667,1.188 3.865,1.438 0.198,0.25 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 107.9 mm (4.25 in.) B 95.7 mm (3.77 in.)
C 201 mm (7.91 in.) D 102 mm (4.02 in.)




NO. 1 BACK DOOR NAME PLATE


B435986C01
4.76,1.302 4.917,1.448 false 6.177,1.292 5.969,1.385 false 6.667,0.948 6.521,0.948 false 4.969,1.427 5.281,1.583 0.313,0.156 10 false *a 6.729,0.865 7.021,1.073 0.292,0.208 10 false *b 5.76,1.344 6.073,1.5 0.313,0.156 10 false *a 4.427,1.438 4.656,1.656 0.229,0.219 10 false A 5.438,2.146 5.667,2.365 0.229,0.219 10 false B 6.229,1.823 6.458,2.042 0.229,0.219 10 false C 6.74,1.281 6.969,1.5 0.229,0.219 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 32.5 mm (1.28 in.) B 146.1 mm (5.75 in.)
C 18.4 mm (0.724 in.) D 18 mm (0.709 in.)



NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


a.

for HYBRID Plate:

B435982C01
4.01,1.583 4.198,1.427 false 5.406,1.563 5.594,1.406 false 6.365,1.948 6.521,1.948 false 4.25,1.323 4.563,1.479 0.313,0.156 10 false *a 6.573,1.875 6.885,2.031 0.313,0.156 10 false *b 5.625,1.302 5.938,1.458 0.313,0.156 10 true *a 3.396,1.198 3.604,1.406 0.208,0.208 10 false A 5.083,0.24 5.292,0.448 0.208,0.208 10 false B 5.906,0.5 6.115,0.708 0.208,0.208 10 false C 6.896,1.135 7.104,1.344 0.208,0.208 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 98.5 mm (3.88 in.) B 231.9 mm (9.13 in.)
C 103.3 mm (4.07 in.) D 102.3 mm (4.03 in.)



b.

for PRIUS Plate:

B435985C01
3.938,1.573 4.094,1.458 false 5.417,1.594 5.573,1.479 false 6.365,1.917 6.5,1.917 false 4.188,1.344 4.5,1.5 0.313,0.156 10 false *a 6.521,1.823 6.833,1.979 0.313,0.156 10 false *b 5.604,1.365 5.917,1.521 0.313,0.156 10 true *a 3.385,1.24 3.573,1.448 0.188,0.208 10 false A 5.083,0.271 5.271,0.479 0.188,0.208 10 false B 5.927,0.594 6.115,0.802 0.188,0.208 10 false C 6.854,1.115 7.042,1.323 0.188,0.208 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 95.7 mm (3.77 in.) B 238.9 mm (9.41 in.)
C 103.7 mm (4.08 in.) D 104.1 mm (4.10 in.)