Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM
NM3210E _51 Engine / Hybrid System _049523 2ZR-FXE ENGINE CONTROL _0249540 SFI SYSTEM DE DETAILS F

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  DETAILS  CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

A pick-up coil type crank position sensor is used. The timing rotor of the crankshaft consists of 34 teeth with 2 teeth missing. The crank position sensor outputs a crankshaft rotation signal every 10°, and the change in the signal due to the missing teeth is used to determine top-dead-center.


b.

A Magneto-Resistance Element (MRE) type cam position sensor is used. To detect the camshaft position, a timing rotor that is part of the camshaft is used to generate 3 pulses (3 high output, 3 low output) for every 2 revolutions of the crankshaft.

W131816C01
0.604,0.75 0.813,0.75 0.813,0.75 1.156,1.125 true 0.74,2.427 0.948,2.427 0.948,2.427 1.719,1.938 true 4.76,0.521 4.969,0.521 4.969,0.521 5.479,0.917 true 5.438,2.417 5.865,3.271 5.865,3.271 6.083,3.271 true 0.427,0.656 0.656,0.844 0.229,0.188 10 false *1 0.521,2.323 0.719,2.542 0.198,0.219 10 false *2 4.573,0.438 4.781,0.646 0.208,0.208 10 false *3 6.125,3.167 6.344,3.365 0.219,0.198 10 false *4
*1 Crank Position Sensor *2 Crankshaft Timing Sprocket
*3 Cam Position Sensor *4 Timing Rotor


Sensor Output Waveforms
W108997E03
4.24,3.625 4.354,4.438 4.354,4.438 4.531,4.438 true 0.948,2.365 1.177,2.604 0.229,0.24 10 false 0V 0.958,1.448 1.188,1.688 0.229,0.24 10 false 5V 0.146,1.198 0.708,2.073 0.563,0.875 10 false Cam Position Sensor Signal 0.125,3.25 0.688,4.042 0.563,0.792 10 false Crank Position Sensor Signal 0.917,3.542 1.146,3.781 0.229,0.24 10 false 0V 4.594,4.375 5.677,4.615 1.083,0.24 10 false 2 Teeth Missing 3.792,0.594 4.708,0.792 0.917,0.198 10 false 720°CA 1.771,1.083 2.688,1.281 0.917,0.198 10 false 180°CA 2.729,2.906 3.646,3.104 0.917,0.198 10 false 360°CA 4.083,1.094 5,1.292 0.917,0.198 10 false 180°CA 5.323,1.104 6.24,1.302 0.917,0.198 10 false 180°CA 5.135,2.917 6.052,3.115 0.917,0.198 10 false 360°CA 2.917,1.083 3.833,1.281 0.917,0.198 10 false 180°CA 1.667,4.438 2.583,4.635 0.917,0.198 10 false 30°CA 2.323,4.438 3.24,4.635 0.917,0.198 10 false 10°CA


c.

The MRE type sensor consists of a magnet and a sensor with a built-in MRE. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to either high or low. The ECM detects the cam position based on this output voltage.


d.

The differences between an MRE type sensor and a conventional pick-up coil type sensor are as follows.

Sensor Type MRE Pick-up Coil
Signal Output Constant digital output starts from low engine speeds. Analog output changes with the engine speeds.
Crankshaft Position and Camshaft Position Detection
·

Detected by comparing the NE signals with the switching of the high/low output that results from the protruding and non-protruding portions of the timing rotor.

·

Can also be detected based on the number of NE signals input during high/low outputs.


Detected by comparing the NE signals with the change of waveform that is output when the protruding portion of the timing rotor passes.

W100950E15
4.313,2.719 4.583,3.344 4.583,3.344 4.729,3.344 true 4.833,1.885 5.24,1.031 5.24,1.031 5.385,1.031 true 1.354,0.271 2.26,0.552 0.906,0.281 12 false MRE Type: 4.688,0.281 6.208,0.563 1.521,0.281 12 false Pick-up Coil Type: 5.427,0.958 6.302,1.302 0.875,0.344 10 false No Detection 4.771,3.271 5.646,3.625 0.875,0.354 10 false No Detection 0.26,1.365 0.74,1.875 0.479,0.51 10 false Engine Speed 0.26,2.448 0.74,2.958 0.479,0.51 10 false Sensor Output 3.573,2.396 4.052,2.896 0.479,0.5 10 false Sensor Output 6.354,2.75 6.813,3.396 0.458,0.646 10 false Analog Output 2.844,2.5 3.281,3.063 0.438,0.563 10 false Digital Output 3.573,1.323 4.042,1.844 0.469,0.521 10 false Engine Speed