Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the power switch off. Wait for at least 2 seconds, then turn the power switch on (IG). The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag ECU assembly constantly monitors the airbag system for malfunctions.

HINT:
If malfunctions are detected during the constant check, the airbag ECU assembly will indicate the malfunction as follows:
·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the power switch is turned on (IG).


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when the power switch is turned from off to on (IG).


HINT:

The SRS warning light will remain illuminated if any airbag or pretensioner has been deployed.





SRS WARNING LIGHT CHECK


a.
C265591

Turn the power switch on (IG), and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the power switch is turned on (IG) (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but DTCs are not output.

·

The power switch is turned from off to on (IG), but the SRS warning light does not come on.





FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)


a.

Initial check

i.

Turn the power switch on (IG).


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.


iii.

Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.

Indicator Operation
Airbag Cut Off Switch Cylinder Sub-assembly Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON ON OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON

HINT:

If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for Trouble in Passenger Airbag ON/OFF Indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>Trouble in Passenger Airbag ON/OFF Indicator


C284690E18
0.333,0.427 1.635,1 1.302,0.573 10 false Power Switch 1.667,0.24 2.74,0.833 1.073,0.594 10 false On (IG) 1.667,0.656 2.76,1.094 1.094,0.438 10 false OFF 1.667,1.344 2.917,1.75 1.25,0.406 10 false ON 1.667,1.708 2.74,2.167 1.073,0.458 10 false OFF 1.667,2.344 2.76,2.75 1.094,0.406 10 false ON 1.667,2.708 2.5,3.229 0.833,0.521 10 false OFF 0.333,1.323 1.469,2.333 1.135,1.01 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.333,2.333 1.469,3.333 1.135,1 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.25,1 4.521,2.667 1.271,1.667 10 false 4 sec. 3.25,2 4.583,2.667 1.333,0.667 10 false 4 sec. 4.167,1 5.5,1.417 1.333,0.417 10 false 2 sec. 4.167,2 5.5,2.417 1.333,0.417 10 false 2 sec. 4.208,3.083 7.156,3.573 2.948,0.49 10 false ON/OFF condition depends on the airbag cut off switch cylinder sub-assembly status result.




FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Occupant Classification System)


a.

Initial check

i.

Turn the power switch on (IG).


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.


iii.

Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation
Front Passenger Seat Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
Vacant OFF ON OFF
Adult*1 is seated ON OFF OFF
Child*2 is seated ON or OFF*2 OFF or ON*2 OFF
Child restraint system is installed OFF ON OFF
Occupant classification system failure OFF ON ON

*1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.

*2: The system may not recognize a child or a child in a child restrain system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.


HINT:
·

The passenger airbag ON/OFF indicator illuminates based on the following timing chart in order to check the indicator light circuit.

·

When the occupant classification system is malfunctioning, both the SRS warning light and passenger airbag ON/OFF indicator ("OFF") come on. In this case, perform troubleshooting for the airbag system DTCs first.



C284690E19
0.333,0.427 1.635,1 1.302,0.573 10 false Power Switch 1.667,0.24 2.74,0.833 1.073,0.594 10 false On (IG) 1.667,0.656 2.76,1.094 1.094,0.438 10 false OFF 1.667,1.344 2.917,1.75 1.25,0.406 10 false ON 1.667,1.708 2.74,2.167 1.073,0.458 10 false OFF 1.667,2.344 2.76,2.75 1.094,0.406 10 false ON 1.667,2.708 2.5,3.229 0.833,0.521 10 false OFF 0.333,1.323 1.469,2.333 1.135,1.01 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.333,2.333 1.469,3.333 1.135,1 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.25,1 4.521,2.667 1.271,1.667 10 false 4 sec. 3.25,2 4.583,2.667 1.333,0.667 10 false 4 sec. 4.167,1 5.5,1.417 1.333,0.417 10 false 2 sec. 4.167,2 5.5,2.417 1.333,0.417 10 false 2 sec. 4.615,3.104 6.75,3.625 2.135,0.521 10 false ON/OFF condition depends on the front passenger detection result.




PASSENGER AIRBAG ON/OFF INDICATOR CHECK (w/ Airbag Cut Off Switch or Occupant Classification System)


a.

Turn the power switch on (IG).

C348299C01
0.333,0.188 0.75,0.438 0.417,0.25 10 false *A 0.333,2.083 0.667,2.323 0.333,0.24 10 false *B 4.167,1.052 4.75,1.469 0.583,0.417 10 false *C
*A for LHD with Airbag Cut Off Switch *B for RHD with Airbag Cut Off Switch
*C w/ Occupant Classification System - -



b.

Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

HINT:

Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the power switch is turned on (IG) and approximately 6 seconds elapse.




FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C348301E01
0.167,0.083 1.833,0.333 1.667,0.25 12 false Connectors of ECU: 0.167,2.208 2.917,2.625 2.75,0.417 12 false Connectors of Sensor Circuit: 0.167,5.583 2.917,6 2.75,0.417 12 false Connectors of Squib Circuit: 0.49,1.781 2.156,2.125 1.667,0.344 10 false to SRS Parts and Sensors 0.604,0.594 2.198,1.031 1.594,0.438 10 false Airbag ECU Assembly 0.583,0.948 0.906,1.344 0.323,0.396 10 false 1 1.281,0.948 1.604,1.344 0.323,0.396 10 false 2 1.979,0.948 2.302,1.344 0.323,0.396 10 false 3 1.26,1.146 1.583,1.542 0.323,0.396 10 false A 0.583,1.354 0.906,1.75 0.323,0.396 10 false 4 1.281,1.354 1.604,1.75 0.323,0.396 10 false 5 1.979,1.354 2.302,1.75 0.323,0.396 10 false 6 2.188,2.688 2.51,3.083 0.323,0.396 10 false 1 2.406,2.688 2.729,3.083 0.323,0.396 10 false 2 3.458,2.688 3.781,3.083 0.323,0.396 10 false 3 3.667,2.688 3.99,3.083 0.323,0.396 10 false 4 3.938,2.625 5.896,2.906 1.958,0.281 10 false Front Airbag Sensor LH/RH 3.458,3.365 3.781,3.76 0.323,0.396 10 false 5 3.677,3.365 4,3.76 0.323,0.396 10 false 6 3.458,3.875 3.781,4.271 0.323,0.396 10 false 7 3.667,3.875 3.99,4.271 0.323,0.396 10 false 8 2.188,4.375 2.51,4.771 0.323,0.396 10 false 9 2.354,4.375 2.677,4.771 0.323,0.396 10 false 10 3.417,4.375 3.74,4.771 0.323,0.396 10 false 11 3.635,4.375 3.958,4.771 0.323,0.396 10 false 12 3.938,3.302 6.479,3.583 2.542,0.281 10 false Side Airbag Sensor Assembly LH/RH 3.938,3.813 6.479,4.094 2.542,0.281 10 false Rear Airbag Sensor LH/RH 3.938,4.313 6.479,4.594 2.542,0.281 10 false Door Side Airbag Sensor LH/RH 3.938,4.99 7.021,5.271 3.083,0.281 10 false Side No. 2 Airbag Sensor Assembly LH/RH 3.417,5.052 3.74,5.448 0.323,0.396 10 false 13 3.635,5.052 3.958,5.448 0.323,0.396 10 false 14 2.656,6.052 5.74,6.333 3.083,0.281 10 false Spiral Cable Sub-assembly 2.188,6.104 2.51,6.5 0.323,0.396 10 false 1 2.396,6.104 2.719,6.5 0.323,0.396 10 false 2 5.094,6.104 5.417,6.5 0.323,0.396 10 false 4 4.885,6.104 5.208,6.5 0.323,0.396 10 false 3 5.344,6.052 6.865,6.417 1.521,0.365 10 false Horn Button Assembly 2.188,6.771 2.51,7.167 0.323,0.396 10 false 5 2.396,6.771 2.719,7.167 0.323,0.396 10 false 6 3.458,6.771 3.781,7.167 0.323,0.396 10 false 7 3.677,6.771 4,7.167 0.323,0.396 10 false 8 3.917,6.719 6.896,7.083 2.979,0.365 10 false Instrument Panel Passenger Airbag Assembly 3.458,7.448 3.781,7.844 0.323,0.396 10 false 9 3.625,7.448 3.948,7.844 0.323,0.396 10 false 10 3.417,8.125 3.74,8.521 0.323,0.396 10 false 11 3.625,8.125 3.948,8.521 0.323,0.396 10 false 12 3.417,8.792 3.74,9.188 0.323,0.396 10 false 13 3.625,8.792 3.948,9.188 0.323,0.396 10 false 14 0.167,3.583 1.135,4.073 0.969,0.49 10 false to Airbag ECU Assembly 0.167,7.292 1.125,7.927 0.958,0.635 10 false to Airbag ECU Assembly 3.917,7.385 6.896,7.75 2.979,0.365 10 false Front Seat Airbag Assembly LH/RH 3.917,8.073 6.896,8.438 2.979,0.365 10 false Front Seat Cushion Airbag Assembly RH 3.917,8.74 6.896,9.104 2.979,0.365 10 false Other SRS Parts* 0.167,9.167 6.781,9.625 6.615,0.458 10 false *: Lower No. 1 Instrument Panel Airbag Assembly, Curtain Shield Airbag Assembly LH/RH, Front Seat Outer Belt Assembly LH/RH and Rear Seat 3 Point Type Outer Belt Assembly LH/RH

Connector Type Application
ECU Sensor Circuit Squib Circuit
Terminal Twin-lock Mechanism Connectors 4, 5, 6 Connectors 1, 9, 10 Connectors 1, 5, 6
Half Connection Prevention Mechanism - - Connectors 1, 5, 11
Activation Prevention Mechanism Connectors 4, 5, 6 - Connectors 2, 4, 6, 8, 10, 12, 14
Connector Lock Mechanism (1) - - Connectors 3, 7, 13
Connector Position Assurance Mechanism - Connectors 2, 3, 5, 7, 11, 13 Connectors 9
Connector Lock Mechanism (2) Connector A - -
Improper Connection Prevention Lock Mechanism Connector A - -


b.

Terminal twin-lock mechanism

C190972E05
2.438,0.094 2.052,0.094 false 2.813,0.656 2.438,0.094 false 5.708,0.094 5.573,0.094 false 5.854,0.635 5.708,0.094 false 0.729,0.01 2.083,0.188 1.354,0.177 10 Lance (Primary Lock) 1.229,1.448 2.167,1.625 0.938,0.177 10 Primary Lock 4.021,0.01 5.698,0.188 1.677,0.177 10 Spacer (Secondary Lock) 4.896,1.427 5.948,1.604 1.052,0.177 10 Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E14
1.427,1.083 1.271,1.083 false 1.531,1.417 1.427,1.083 false 1.719,0.813 1.5,0.813 false 1.833,1.375 1.719,0.813 false 2.146,0.531 1.938,0.531 false 2.354,1.333 2.146,0.531 false 3.219,0.563 3.406,0.563 false 3.01,1.208 3.219,0.563 false 3.458,0.865 3.635,0.865 false 3.198,1.313 3.458,0.865 false 5.917,0.74 5.729,0.74 false 6.063,1.156 5.917,0.74 false 1.125,0.458 1.958,0.667 0.833,0.208 10 Locking Arm 0.979,0.729 1.531,0.927 0.552,0.198 10 Stopper 0.469,1 1.323,1.25 0.854,0.25 10 Locking Part 3.448,0.5 3.885,0.688 0.438,0.188 10 Slider 3.667,0.802 4.135,0.99 0.469,0.188 10 Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 Stopper 4.615,1.969 6.01,2.344 1.396,0.375 10 Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E02
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 false 1.844,1.667 1.844,2.083 false 1.656,1.448 1.198,1.448 false 2.646,1.646 2.969,1.646 false 2.354,1.385 3,0.969 3,0.969 2.552,1.458 false 1.771,0.375 2.51,0.708 0.74,0.333 10 When open 0.313,0.833 1.208,1.146 0.896,0.313 10 Male Housing 3.042,0.885 4.115,1.229 1.073,0.344 10 Female Terminal 0.302,1.375 1.198,1.698 0.896,0.323 10 Male Terminal 3.01,1.573 4.073,1.938 1.063,0.365 10 Female Housing 1.26,2.104 2.448,2.448 1.188,0.344 10 Short Spring Plate 5.448,0.375 6.354,0.75 0.906,0.375 10 When shorted 4.375,2.063 6.156,2.635 1.781,0.573 10 Short spring plate contacting the male terminal

i.

This mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E03
2.521,0.344 2.021,0.198 false 2.635,0.76 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.927,1.031 1.646,0.427 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector locking button engages the locking button claws in the grooves on the other side of the connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E04
0.854,0.198 1.021,0.198 false 0.833,1.104 0.854,0.198 false 1.052,0.479 1.219,0.479 false 0.927,1.25 1.052,0.479 false 0.729,2.292 0.958,2.292 false 0.51,1.792 0.729,2.292 false 5.635,0.781 5.469,0.781 false 5.646,1.156 5.635,0.781 false 1.063,0.125 2.271,0.354 1.208,0.229 10 Female Connector 1.26,0.406 2.094,0.656 0.833,0.25 10 Locking Part 1.0,2.219 2.042,2.469 1.042,0.25 10 Male Connector 2.958,0.302 4.542,0.573 1.583,0.271 10 Primary Lock Completed 5.073,0.302 6.844,0.573 1.771,0.271 10 Secondary Lock Completed 4.896,0.698 5.521,0.875 0.625,0.177 10 Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C204951E05
1.135,1.385 1.135,1.813 1.135,1.813 0.854,1.813 false 1.792,3.198 1.792,3.583 1.792,3.583 2.302,3.583 false 4.156,2.76 4.156,3.063 4.156,3.063 3.896,3.063 false 6.115,3.344 5.75,3.344 false 6.458,2.75 6.583,2.75 false 6.323,2.729 6.094,2.729 false 4.385,1.448 4.646,1.448 false 0.458,1.74 0.896,2.115 0.438,0.375 10 Lance 4.688,1.375 5.208,1.677 0.521,0.302 10 Holder 2.323,3.521 2.885,3.771 0.563,0.25 10 Retainer 5.208,3.25 5.854,3.51 0.646,0.26 10 Retainer 3.344,2.979 3.948,3.323 0.604,0.344 10 Retainer 5.667,2.656 6.146,2.969 0.479,0.313 10 Holder 6.625,2.667 7.031,2.917 0.406,0.25 10 Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C204952E09
5.292,0.792 5.292,0.219 5.292,0.219 5.656,0.219 false 5.292,1.167 5.292,1.875 5.292,1.875 4.604,1.875 false 4.958,3.01 4.583,3.01 false 1.104,1.479 1.104,2.396 1.104,2.396 0.948,2.396 false 1.021,1.188 1.021,0.521 1.021,0.521 1.333,0.521 false 6,0.719 6,1.031 6,1.031 5.51,1.031 false 3.958,0.073 4.573,0.448 0.615,0.375 10 Top View 0.25,2.323 0.958,2.74 0.708,0.417 10 Unlock Rib 3.917,1.781 4.604,2.333 0.688,0.552 10 Temporary Hold Lock 4.219,2.927 4.625,3.24 0.406,0.313 10 Lever 5.698,0.146 6.448,0.438 0.75,0.292 10 Unlock Rib 1.375,0.448 1.594,0.698 0.219,0.25 10 A 5.958,0.563 6.219,0.802 0.26,0.24 10 A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag ECU assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector of the airbag system squib circuit to prevent accidental airbag and pretensioner deployment.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag and pretensioner deployment.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specified by the troubleshooting procedure.

·

To prevent the terminals and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



w/o Passenger Airbag ON/OFF Indicator:
C247429E16
1.594,0.458 1.927,0.677 0.333,0.219 3.719,0.458 4.073,0.688 0.354,0.229 5.354,0.458 5.719,0.688 0.365,0.229 0.146,5.042 0.479,5.26 0.333,0.219 0.708,6.135 1.042,6.354 0.333,0.219 2.792,2.781 3.167,2.26 3.167,2.26 2.802,2.479 false 2.198,2.854 1.771,3.281 1.771,3.281 2.198,2.563 false 5.188,2.573 4.719,3.302 4.719,3.302 5.188,2.875 false 5.656,2.781 6.083,2.219 6.083,2.219 5.677,2.479 false 6.229,4.813 6.313,4.448 6.313,4.448 6.375,4.448 false 4.073,4.813 4.198,4.427 4.198,4.427 4.26,4.427 false 5.417,4.76 5.417,5.51 false 3.313,4.75 3.313,5.5 false 3.875,6.531 3.781,6.531 3.781,6.531 3.667,6.875 false 3.125,7.01 3.313,7.365 3.313,7.365 3.385,7.365 false 6.594,6.531 6.5,6.531 6.5,6.531 6.385,6.875 false 5.844,7.01 6.021,7.365 6.021,7.365 6.104,7.365 false 1.521,1.865 2.469,2.208 0.948,0.344 10 false Before Release 4.615,1.865 5.49,2.229 0.875,0.365 10 false After Release 3.198,2.146 3.604,2.5 0.406,0.354 10 false Paper 6.115,2.135 6.531,2.625 0.417,0.49 10 false Paper 1.375,3.281 2.198,3.604 0.823,0.323 10 false Short Spring 4.313,3.333 5.125,3.688 0.813,0.354 10 false Short Spring 1.656,0.49 2.708,0.854 1.052,0.365 10 false F56 0.094,0.063 4.115,0.344 4.021,0.281 12 false Wire harness connector (to Airbag ECU Assembly): 2.938,4.125 3.906,4.479 0.969,0.354 10 false Before Release 2.521,6.156 3.531,6.552 1.01,0.396 10 false Before Release 5.208,4.125 6.104,4.479 0.896,0.354 10 false After Release 5.188,6.167 6.031,6.542 0.844,0.375 10 false After Release 3.896,6.427 4.302,6.792 0.406,0.365 10 false Paper 4.281,4.344 4.781,4.74 0.5,0.396 10 false Paper 6.396,4.365 6.906,4.823 0.51,0.458 10 false Paper 3.406,7.271 4.24,7.667 0.833,0.396 10 false Short Spring 2.927,5.51 3.74,5.958 0.813,0.448 10 false Short Spring 5.021,5.531 5.844,5.938 0.823,0.406 10 false Short Spring 6.615,6.427 7.031,6.813 0.417,0.385 10 false Paper 6.125,7.271 6.969,7.656 0.844,0.385 10 false Short Spring 0.094,3.75 3.219,4.042 3.125,0.292 12 false Spiral Cable Sub-assembly Connector: 0.115,5.802 3.604,6.115 3.49,0.313 12 false No. 2 Instrument Panel Wire Connector: 0.542,7.458 1.625,7.802 1.083,0.344 10 false : Short Spring 3.813,0.49 4.865,0.854 1.052,0.365 10 false M2 5.417,0.49 6.469,0.854 1.052,0.365 10 false M44 0.208,5.073 1.26,5.438 1.052,0.365 10 false F22 0.76,6.167 1.813,6.531 1.052,0.365 10 false FX2

w/ Passenger Airbag ON/OFF Indicator:
C247452E20
1.75,0.49 2.125,0.74 0.375,0.25 3.417,0.49 3.75,0.74 0.333,0.25 5.083,0.49 5.417,0.74 0.333,0.25 0.156,5.01 0.49,5.229 0.333,0.219 0.677,6.271 1.01,6.49 0.333,0.219 3.094,2.823 3.469,2.302 3.469,2.302 3.063,2.51 false 2.479,2.917 2.104,3.333 2.104,3.333 2.49,2.615 false 5.042,2.625 4.604,3.354 4.604,3.354 5.052,2.938 false 5.5,2.823 5.979,2.271 5.979,2.271 5.521,2.51 false 6.229,4.76 6.313,4.396 6.313,4.396 6.375,4.396 false 4.01,4.76 4.135,4.365 4.135,4.365 4.198,4.365 false 3.927,6.563 3.833,6.563 3.833,6.563 3.74,6.938 false 6.49,6.573 6.396,6.573 6.396,6.573 6.313,6.938 false 3.271,7.063 3.469,7.281 3.469,7.281 3.552,7.281 false 5.813,7.052 6.021,7.281 6.021,7.281 6.094,7.281 false 5.417,4.708 5.417,5.469 false 3.271,4.708 3.271,5.458 false 0.083,0.052 4.438,0.323 4.354,0.271 12 false Wire harness connector (to Airbag ECU Assembly): 1.833,1.917 2.792,2.25 0.958,0.333 10 false Before Release 4.479,1.917 5.365,2.292 0.885,0.375 10 false After Release 3.49,2.198 3.875,2.5 0.385,0.302 10 false Paper 5.99,2.188 6.385,2.594 0.396,0.406 10 false Paper 1.719,3.333 2.49,3.677 0.771,0.344 10 false Short Spring 4.198,3.385 4.979,3.719 0.781,0.333 10 false Short Spring 2.938,4.073 3.885,4.333 0.948,0.26 10 false Before Release 2.521,6.229 3.479,6.521 0.958,0.292 10 false Before Release 5.198,4.073 6.104,4.396 0.906,0.323 10 false After Release 5.115,6.229 5.979,6.521 0.865,0.292 10 false After Release 3.969,6.5 4.396,6.771 0.427,0.271 10 false Paper 4.229,4.292 4.635,4.448 0.406,0.156 10 false Paper 6.531,6.5 6.948,6.802 0.417,0.302 10 false Paper 6.417,4.323 6.844,4.604 0.427,0.281 10 false Paper 3.604,7.198 4.375,7.542 0.771,0.344 10 false Short Spring 6.135,7.198 6.917,7.542 0.781,0.344 10 false Short Spring 0.083,3.688 3.479,4.021 3.396,0.333 12 false Spiral Cable Sub-assembly Connector: 0.083,5.844 3.5,6.177 3.417,0.333 12 false No. 2 Instrument Panel Wire Connector: 0.521,7.469 1.406,7.76 0.885,0.292 10 false : Short Spring 2.896,5.458 3.688,5.802 0.792,0.344 10 false Short Spring 5.021,5.479 5.813,5.813 0.792,0.333 10 false Short Spring 1.813,0.531 2.229,0.771 0.417,0.24 10 false M45 3.469,0.531 3.885,0.771 0.417,0.24 10 false F56 5.167,0.531 5.583,0.771 0.417,0.24 10 false M1 0.208,5.042 0.625,5.281 0.417,0.24 10 false F22 0.74,6.302 1.156,6.542 0.417,0.24 10 false FX1