Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0227085 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

HINT:
·

If any DTCs are output, the value for a measurement item may be incorrect.

·

If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using the Data List.



Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cruise Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual vehicle speed -
Cruise Memory Vehicle Speed Stored vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual stored vehicle speed -
Cruise Request Throttle Opening Angle Cruise requested position 0 to 124.99° When cruise is set (vehicle in motion at 80 km/h [50 mph]): Actual requested throttle position -
Vehicle Acceleration Acceleration condition while driving the vehicle -13.1 to 13.1 m/s2 Current value displayed -
Cruise Target Acceleration Target acceleration while in cruise control mode -13.1 to 13.1 m/s2 Current value displayed -
Driving Support ECU Target Acceleration Target acceleration from driving support ECU assembly -13.1 to 13.1 m/s2 - This item is displayed on the GTS but is not used
Acceleration Continuation Decision Acceleration continuation decision condition ON or OFF - This item is displayed on the GTS but is not used
Output Driving Force Generated drive torque -10 to 9.92 kN - This item is displayed on the GTS but is not used
Cruise Request Driving Force Cruise request torque signal -10 to 9.92 kN Differs according to the cruise control system condition -
Cruise Request Driving Force Feedback Status Cruise request driving force feedback mode No Control/Suspend/Neg Calc Prohibited/Pos Calc Prohibited/Normal/Increasing at Start - This item is displayed on the GTS but is not used
Cruise Control Permission Condition Cruise control permission condition OK or NG - This item is displayed on the GTS but is not used
Cruise Control Condition Cruise control system condition No Control/Constant Speed Control Mode - Ready/ - This item is displayed on the GTS but is not used
Cruise Control Mode Cruise control mode condition No Control/Constant Speed Control Mode No Control: Cruise control mode not operating
Constant Speed Control Mode: Constant speed control mode operating
-
Cruise Request Gear Position Shift request from hybrid vehicle control ECU None or 255 Gear Shift request from cruise control displayed -
Cruise Acceleration and Deceleration Operation Condition Cruise acceleration and deceleration operation condition No Control/Constant Speed Control Mode - Standby/Constant Speed Control Mode - RES SW Control/Constant Speed Control Mode - COAST SW Control/Vehicle Distance Control Mode - Acceleration Operation - This item is displayed on the GTS but is not used
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF switch) signal ON or OFF ON: Cruise control main switch (ON-OFF switch) pushed
OFF: Cruise control main switch (ON-OFF switch) released
-
Cruise Ready Main-CPU Cruise control system standby condition (Main-CPU) ON or OFF ON: Cruise control main switch (Main-CPU) SET
OFF: Cruise control main switch (Main-CPU) UNSET
-
Cruise Ready Sub-CPU Cruise control system standby condition (Sub-CPU) ON or OFF ON: Cruise control main switch (Sub-CPU) SET
OFF: Cruise control main switch (Sub-CPU) UNSET
-
Accelerator Pedal Condition of the accelerator pedal during cruising ON or OFF ON: Accelerator pedal depressed
OFF: Accelerator pedal released
-
Cruise Brake Cancel Switch Cruise control brake cancel condition ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch Main-CPU Stop light switch signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch Sub-CPU Stop light switch signal ON or OFF - This item is displayed on the GTS but is not used
Request Manual Cancel Whether there is a manual cancel request ON or OFF - This item is displayed on the GTS but is not used
Request Automatic Cancel Whether there is an automatic cancel request ON or OFF - This item is displayed on the GTS but is not used
Cruise Brake Control Decision Cruise brake control decision ON or OFF ON: Cruise brake activated
OFF: Cruise brake deactivated
-
Cruise Brake Control Permission Condition Cruise brake control permission condition OK or NG - This item is displayed on the GTS but is not used
Cruise Indicator Cruise control indicator light signal ON or OFF ON: Cruise control indicator light turns on
OFF: Cruise control indicator light turns off
-
Wheel Speed Sensor and Deceleration Sensor Wheel speed sensor and deceleration sensor signal Avail or Not Avl Avail: Wheel speed sensor/Deceleration sensor available
Not Avl: Wheel speed sensor/Deceleration sensor not available
-
Gradient of Road Surface Gradient of road surface condition -32.76 to 32.76 m/s2 - This item is displayed on the GTS but is not used


PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

HINT:

The power switch must be turned on (IG) to proceed with the Active Test using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -