Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a short to ground in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted via CAN communication to each ECU including the airbag ECU assembly. Thus when multiple systems do not enter DTC output mode, there may be a malfunction in the hybrid vehicle control ECU.



WIRING DIAGRAM

C339485E02
0.75,4.438 4.417,4.635 3.667,0.198 10 false : CAN Communication Line 0.5,3.927 2.979,4.188 2.479,0.26 10 false Hybrid Vehicle Control ECU 5.677,2.01 7.156,2.292 1.479,0.281 10 false Airbag ECU Assembly 5.667,1.844 6.385,2.188 0.719,0.344 10 false F56 5.958,0.667 6.948,1 0.99,0.333 10 false CANH 5.969,1.406 6.958,1.74 0.99,0.333 10 false CANL 0.927,0.677 1.917,1.01 0.99,0.333 10 false CA3N 0.938,1.406 1.927,1.74 0.99,0.333 10 false CA3P 1.115,2.771 2.104,3.104 0.99,0.333 10 false TC 1.458,2.771 2.448,3.104 0.99,0.333 10 false F3 1.458,1.417 2.448,1.75 0.99,0.333 10 false F2 1.458,0.688 2.448,1.021 0.99,0.333 10 false F2 1.458,0.469 1.76,0.729 0.302,0.26 10 false 20 1.5,1.208 1.802,1.469 0.302,0.26 10 false 7 1.458,2.563 1.76,2.823 0.302,0.26 10 false 30 5.708,0.521 6.01,0.781 0.302,0.26 10 false 13 5.719,1.229 6.021,1.49 0.302,0.26 10 false 22 5.938,3.906 6.375,4.146 0.438,0.24 10 false F29 5.938,4.052 6.375,4.292 0.438,0.24 10 false DLC3 5.969,2.76 6.406,3 0.438,0.24 10 false TC 5.719,2.646 6.021,2.906 0.302,0.26 10 false 13 5.958,3.354 6.396,3.594 0.438,0.24 10 false CG 5.802,3.271 6.104,3.531 0.302,0.26 10 false 4

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF HYBRID VEHICLE CONTROL ECU)
a.
C339779C02
0.281,1.083 0.635,1.344 0.354,0.26 0.281,3.219 0.635,3.479 0.354,0.26 1.344,2.021 2.073,1.531 false 0.781,4.167 1.396,3.552 false 0.24,0.271 1.01,2.823 0.771,2.552 10 false *1 0.26,2.292 0.656,2.604 0.396,0.313 10 false *a 0.344,1.135 0.688,1.396 0.344,0.26 10 false F29 0.385,3.271 0.729,3.531 0.344,0.26 10 false F3 1.146,1.948 1.594,2.229 0.448,0.281 10 false TC 0.583,4.094 1.031,4.375 0.448,0.281 10 false TC
*1 DLC3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Turn the power switch off.


b.

Disconnect the connector from the hybrid vehicle control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-13 (TC) - F3-30 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C57
0.146,0.625 0.49,0.854 0.344,0.229 1.615,0.813 1.615,0.313 1.615,0.313 1.813,0.313 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *1 0.198,0.656 0.51,0.958 0.313,0.302 10 false F29 1.844,0.24 2.083,0.406 0.24,0.167 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C58
0.156,0.594 0.5,0.823 0.344,0.229 1.958,1.76 1.792,1.76 1.792,1.76 1.792,1.344 false 0.125,0.115 0.406,0.396 0.281,0.281 10 false *1 0.219,0.625 0.781,1.083 0.563,0.458 10 false F29 2.021,1.688 2.354,1.979 0.333,0.292 10 false TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU