Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230366 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

CAUTION:
B417753C01
0.948,0.958 1.104,1.156 0.156,0.198 10 false .
V100155

Deployment Side


When storing the horn button assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B434274

Turn the steering wheel assembly 90° to the left.


d.
B450307C01
1.094,1.813 1.406,2.01 0.313,0.198 10 false *a 1.615,0.313 1.927,0.51 0.313,0.198 10 false *b
V100155

Masking Tape
*a 55 mm (2.17 in.)
*b 95 mm (3.74 in.)


Wrap masking tape around a 6 mm hexagon wrench as shown in the illustration.

HINT:

Use a 6 mm hexagon wrench with a long arm length of approximately 95 mm (3.74 in.).



e.
B450332C01
1.313,1.063 1.313,1.281 false 1.219,1.073 1,1.281 1,1.281 0.823,1.281 false 1.229,1.26 1.438,1.438 0.208,0.177 10 false *a 0.656,1.198 0.865,1.375 0.208,0.177 10 false *b
V100155

Masking Tape
*a Housing Tab
*b Omega Spring


Insert the 6 mm hexagon wrench into the service hole until the masking tape is at the position shown in the illustration.

HINT:

Make sure to insert the 6 mm hexagon wrench into the service hole on the backside of the steering wheel assembly.



f.
B428457C01
1.833,0.688 2.594,0.688 true 1.25,0.896 1.25,1.104 1.25,1.104 0.781,1.104 true 2.646,0.615 2.958,0.771 0.313,0.156 10 false *a 0.604,1.021 0.917,1.177 0.313,0.156 10 false *b
*a Housing Tab
*b Omega Spring


Using the 6 mm hexagon wrench, push down the housing tab to disengage the hook as shown in the illustration.

HINT:

Pushing down the housing tab will push the omega spring and disengage it from the hook.



g.
B428458

Turn the steering wheel assembly 180° to the right.


h.
B450333C01
0.802,1.271 1.042,1.271 1.042,1.271 1.24,1.052 false 1.333,1.271 1.333,1.042 false 1.26,1.281 1.573,1.479 0.313,0.198 10 false *a 0.625,1.198 0.938,1.396 0.313,0.198 10 false *b
V100155

Masking Tape
*a Housing Tab
*b Omega Spring


Insert the 6 mm hexagon wrench into the service hole until the masking tape is at the position shown in the illustration.

HINT:

Make sure to insert the 6 mm hexagon wrench into the service hole on the backside of the steering wheel assembly.



i.
B428459C01
0.885,0.823 1.708,0.823 true 2.292,0.875 2.292,1.042 2.292,1.042 2.771,1.042 true 0.719,0.729 1.031,0.885 0.313,0.156 10 false *a 2.792,0.979 3.104,1.135 0.313,0.156 10 false *b
*a Housing Tab
*b Omega Spring


Using the 6 mm hexagon wrench, push down the housing tab to disengage the hook as shown in the illustration.

NOTICE:

Lightly hold the horn button assembly so that it does not fall.


HINT:

Pushing down the housing tab will push the omega spring and disengage it from the hook.



j.
B450309C01
0.865,1.24 1.333,1.24 true 1.021,1.24 1.021,1.792 1.021,1.792 1.219,1.792 true 0.698,1.167 0.938,1.385 0.24,0.219 10 false *a
*a Spring


Check that each hook is disengaged.

HINT:

If a hook is disengaged, the spring will be visible at the location shown in the illustration.



k.
B450311

Turn the steering wheel assembly 90° to the right.


l.
B428455C01
1.938,0.917 2.104,1.26 2.104,1.26 2.333,1.26 true 2,2.469 2.125,2.646 2.125,2.646 2.354,2.646 true 1.51,0.344 1.729,0.344 1.729,0.344 1.948,0.76 true 1.531,1.823 1.75,1.823 1.75,1.823 1.969,2.24 true 2.365,1.177 2.677,1.333 0.313,0.156 10 false *a 2.385,2.563 2.698,2.719 0.313,0.156 10 false *a 1.333,0.26 1.646,0.417 0.313,0.156 10 false *b 1.365,1.74 1.677,1.896 0.313,0.156 10 false *b
*a Housing Tab
*b Hook


Using a 6 mm hexagon wrench, push the housing tab to disengage the hook as shown in the illustration.

NOTICE:

Lightly hold the horn button assembly so that it does not fall.


HINT:
·

Insert the 6 mm hexagon wrench into the service hole until it contacts the hook and then push down the housing tab while pushing it toward the rear of the vehicle.

·

Pushing down the housing tab will disengage it from the hook.




m.

Turn the steering wheel assembly 180° to the left to align the front wheels facing straight ahead.

NOTICE:

Do not drop the horn button assembly.



n.

Pull out the horn button assembly from the steering wheel assembly and hold the horn button assembly with one hand.

NOTICE:

When separating the horn button assembly, do not pull the airbag wire harness.



o.

w/o Passenger Airbag ON/OFF Indicator:

i.
B432389C01
0.448,0.969 1.49,0.969 true 1.594,0.573 1.781,0.292 1.781,0.292 2.167,0.292 true 0.708,2.583 0.948,2.906 0.948,2.906 1.281,2.906 true 1.677,0.885 2.115,1.365 2.115,1.365 2.448,1.365 true 0.958,0.396 1.271,0.396 1.271,0.396 1.542,0.646 true 0.271,0.875 0.583,1.031 0.313,0.156 10 false *a 2.177,0.198 2.385,0.417 0.208,0.219 10 true *b 1.313,2.823 1.625,2.979 0.313,0.156 10 false *c 2.469,1.271 2.677,1.479 0.208,0.208 10 true *d 0.76,0.302 0.958,0.51 0.198,0.208 10 true *e
*a Airbag Connector
*b Horn Connector
*c Airbag Connector Lock
*d Protective Tape
*e Wire Harness Clamp


Disconnect the horn connector from the horn button assembly.


ii.

Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.


iii.

Disconnect the airbag connector.


iv.

Disengage the wire harness clamp to remove the horn button assembly

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




p.

w/ Passenger Airbag ON/OFF Indicator:

i.
B428460C01
1.604,0.854 0.583,0.854 true 1.604,0.688 1.125,0.688 1.125,0.688 1.125,0.865 true 2.417,0.219 1.938,0.219 1.938,0.219 1.74,0.5 true 0.833,2.76 0.333,2.76 true 2.552,1.219 2.073,1.219 2.073,1.219 1.771,0.781 true 1.656,0.583 1.229,0.333 1.229,0.333 0.906,0.333 true 0.406,0.76 0.719,0.917 0.313,0.156 10 false *a 2.448,0.146 2.667,0.365 0.219,0.219 10 true *b 0.177,2.677 0.49,2.833 0.313,0.156 10 false *c 2.583,1.125 2.792,1.333 0.208,0.208 10 true *d 0.74,0.24 1.052,0.396 0.313,0.156 10 false *e
*a Airbag Connector
*b Horn Connector
*c Airbag Connector Lock
*d Protective Tape
*e Wire Harness Clamp


Disconnect the horn connector from the horn button assembly.


ii.

Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.


iii.

Disconnect the 2 airbag connectors.


iv.

Disengage the wire harness clamp to remove the horn button assembly

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.