84340
1.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/ Canister Pump Module)
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A46 stop light switch assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A46-1 (B) - A46-3 (GND) | Always | 11 to 14 V |
| A46-5 (B) - A46-3 (GND) | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A46-3 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the wire harness or connector.
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Reconnect the A46 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A46-2 (L) - A46-3 (GND) | Brake pedal not depressed | Below 1 V |
| A46-2 (L) - A46-3 (GND) | Brake pedal depressed | 11 to 14 V |
| A46-4 (L) - A46-3 (GND) | Power switch on (IG), brake pedal not depressed | 11 to 14 V |
| A46-4 (L) - A46-3 (GND) | Power switch on (IG), brake pedal depressed | Below 1 V |
If the result is not as specified, replace the stop light switch assembly.
84340
2.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/o Canister Pump Module)
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A47 stop light switch assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-7 (B) - A47-2 (GND) | Power switch off | 11 to 14 V |
| A47-6 (B) - A47-2 (GND) | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-2 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the wire harness or connector.
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Reconnect the A47 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47- 1 (OUT) - A47-2 (GND) | Power switch off, brake pedal not depressed | Below 1 V |
| A47-1 (OUT) - A47-2 (GND) | Power switch off, brake pedal depressed | 11 to 14 V |
| A47-3 (L) - A47-2 (GND) | Power switch off, brake pedal not depressed | Below 1 V |
| A47-3 (L) - A47-2 (GND) | Power switch off, brake pedal depressed | 11 to 14 V |
| A47-4 (ACC) - A47-2 (GND) | Power switch off | 11 to 14 V |
| A47-5 (L) - A47-2 (GND) | Power switch on (IG), brake pedal not depressed | 11 to 14 V |
| A47-5 (L) - A47-2 (GND) | Power switch on (IG), brake pedal depressed | Below 1 V |
If the result is not as specified, replace the stop light switch assembly.