Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0232459 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the R5 rear television camera assembly connector.

E286120E24
3.375,0.083 3.792,0.333 0.417,0.25 3.458,0.125 3.792,0.323 0.333,0.198 10 false R5


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-6 (CB+) - Body ground G - Body ground Power source Power switch on (ACC) 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the R5 rear television camera assembly connector.


d.

Measure the voltage and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-3 (CV+) - R5-2 (CV-) R - B Video signal Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
R5-5 (CGND) - Body ground RB - Body ground Shield ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.

*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type



If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.

*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type



i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal R5-3 (CV+) - R5-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal R5-3 (CV+) - R5-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).






NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


a.

Measure the voltage and check for pulses at each terminal of the connector.

E344906N02
4.938,0.229 5.333,0.479 0.396,0.25 1.51,0.229 1.906,0.479 0.396,0.25 5.01,0.25 5.469,0.448 0.458,0.198 10 false F95 1.573,0.26 2.031,0.458 0.458,0.198 10 false F93

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specification
F93-7 (GND1) - Body ground LA-BR - Body ground Ground Always Below 1 V
F95-11 (CA+) - F93-7 (GND1) B - LA-BR Rear television camera assembly power supply Power switch on (ACC) 5.5 to 7.05 V
F95-12 (V+) - F93-7 (GND1) R - LA-BR Video signal Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out the screen
Pulse generation
(Refer to waveform 2)
F95-23 (CGND) - Body ground Shield - Body ground Shield ground Always Below 1 V
F95-24 (V-) - F93-7 (GND1) W - LA-BR Ground Always Below 1 V

If the result is not as specified, the radio and display receiver assembly may be malfunctioning.


b.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal F95-12 (V+) - F93-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal F95-12 (V+) - F93-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Receiver Type)


a.

Measure the voltage and check for pulses at each terminal of the connector.

E344906E01
4.938,0.229 5.333,0.479 0.396,0.25 1.51,0.229 1.906,0.479 0.396,0.25 5.01,0.25 5.469,0.448 0.458,0.198 10 false F34 1.573,0.26 2.031,0.458 0.458,0.198 10 false F32

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specification
F32-7 (GND1) - Body ground LA-BR - Body ground Ground Always Below 1 V
F34-11 (CA+) - F32-7 (GND1) B - LA-BR Rear television camera assembly power supply Power switch on (ACC) 5.5 to 7.05 V
F34-12 (V+) - F32-7 (GND1) R - LA-BR Video signal Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out the screen
Pulse generation
(Refer to waveform 2)
F34-23 (CGND) - Body ground Shield - Body ground Shield ground Always Below 1 V
F34-24 (V-) - F32-7 (GND1) W - LA-BR Ground Always Below 1 V

If the result is not as specified, the radio and display receiver assembly may be malfunctioning.


b.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal F34-12 (V+) - F32-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal F34-12 (V+) - F32-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).