Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0232459 PARKING ASSIST MONITOR SYSTEM D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE


a.

In diagnostic mode for the parking assist monitor system, signals received by the navigation receiver assembly*1 or radio and display receiver assembly*2 can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display.

*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E311685E01
2.865,0.979 6.073,1.177 3.208,0.198 10 false Start diagnostic mode 0.104,0.063 1.573,0.302 1.469,0.24 12 false Example: 1.99,7.885 2.302,8.083 0.313,0.198 10 false or

E311686E01
1.99,0.688 2.302,0.885 0.313,0.198 10 false or


DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E311687E01
2.865,1.031 4.74,1.271 1.875,0.24 10 false Start diagnostic mode 0.115,0.063 1.583,0.302 1.469,0.24 12 false Example: 1.031,4.313 1.271,4.583 0.24,0.271 10 false or 5.156,5.333 5.396,5.604 0.24,0.271 10 false or

E311688E01
4.51,1.177 4.823,1.375 0.313,0.198 10 false or


VEHICLE SIGNAL CHECK


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


c.
E307209E01
0.083,0.042 1.313,0.24 1.229,0.198 10 false Example:

Select "Vehicle Signal" on the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".


HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly*1 or radio and display receiver assembly*2.

*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type








CAR SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E307209E01
0.083,0.042 1.313,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.

Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting screen



iii.
E286098

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E286093

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
CAN CAN communication signal input When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR





CAMERA SYNCHRONOUS ERROR HISTORY


HINT:

This function is used to check the date and time of occurrence when a camera synchronous error occurs.


a.

Check camera synchronous error history.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Camera Synchronous Error History.

Body Electrical > Navigation System > Utility
Tester Display
Camera Synchronous Error History
50005 212 4285

v.

When an item is stored for Camera Synchronous Error History, record it before repairing the navigation receiver assembly*1 or radio and display receiver assembly*2 and television camera assembly.

*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type


HINT:

Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.




b.

Clear camera synchronous error history.

i.

When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.


·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.






CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION