Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0232459 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering sensor power source
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E288975E42
0.5,0.292 1.896,0.552 1.396,0.26 10 false from IG1 NO. 1 Relay 0.448,0.792 2.021,1.073 1.573,0.281 10 false from Auxiliary Battery 2.24,0.469 3.292,0.677 1.052,0.208 10 false ECU-IG1 NO. 2 2.188,0.938 3.49,1.177 1.302,0.24 10 false ECU-DCC NO. 1 3.313,0.219 3.469,0.417 0.156,0.198 10 false 4 3.302,0.688 3.458,0.885 0.156,0.198 10 false 5 3.302,1.135 3.458,1.333 0.156,0.198 10 false 1 0.927,2.031 2.646,2.292 1.719,0.26 10 false : CAN Communication Line 5.125,1.635 6.583,2.271 1.458,0.635 10 false Rear Television Camera Assembly 3.448,1.635 3.906,1.833 0.458,0.198 10 false F55 3.458,1.792 4.594,2.073 1.135,0.281 10 false Steering Sensor 3.531,0.313 3.99,0.51 0.458,0.198 10 false IG1 3.531,0.802 3.99,1 0.458,0.198 10 false BAT 3.531,1.271 3.99,1.469 0.458,0.198 10 false ESS

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the F55 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F55-4 (IG1) - F55-1 (ESS) Power switch on (IG) 11 to 14 V
F55-5 (BAT) - F55-1 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR