Home › Engine / Hybrid System › 2ZR-FXE COOLING › COOLING SYSTEM › 2015.11–2016.08
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0233433 COOLING SYSTEM G

2ZR-FXE COOLING  COOLING SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A389829

Do not remove the reserve tank cap and air release valve (w/ air release valve) while the engine or radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 1.INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:

Do not remove the reserve tank cap and air release valve (w/ air release valve) while the engine or radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.

Remove the reserve tank cap.


b.

Add engine coolant to the FULL line of the radiator reserve tank assembly.


c.

Install a radiator cap tester.

A390673C01
0.969,0.896 1.177,0.896 1.177,0.896 1.323,0.677 false 4.385,0.896 4.594,0.896 4.594,0.896 4.74,0.677 false 0.375,0.052 0.719,0.333 0.344,0.281 12 false *A 3.813,0.063 4.167,0.333 0.354,0.271 12 false *B 0.823,0.781 1.135,0.938 0.313,0.156 10 false *a 4.25,0.792 4.563,0.948 0.313,0.156 10 false *a
*A w/o Air Release Valve *B w/ Air Release Valve
*a Radiator Cap Tester - -



d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Warm up the engine.


f.

Pump the radiator cap tester to 122 kPa (1.2 kgf/cm2, 17 psi), and then check that the pressure does not drop.

·

If the pressure drops, check the hoses, radiator assembly and engine water pump assembly for leaks.

·

If there are no signs of external engine coolant leaks, check the heater core, cylinder block sub-assembly and cylinder head sub-assembly.



g.

Remove the radiator cap tester.


h.

Install the reserve tank cap.


Hide 2.INSPECT RADIATOR RESERVE TANK ENGINE COOLANT LEVEL (for Engine)

a.

Check that the engine coolant level is between the LOW line and FULL line when the engine is cold.

A390668C02
2.521,0.875 2.865,0.594 2.865,0.594 3.073,0.594 false 2.531,1.031 2.854,1.271 2.854,1.271 3.115,1.271 false 5.188,0.865 5.833,0.583 5.833,0.583 6.063,0.583 false 5.177,1.021 5.813,1.292 5.813,1.292 6.063,1.292 false 0.813,0.031 1.135,0.344 0.323,0.313 12 false *A 3.885,0.031 4.219,0.354 0.333,0.323 12 false *B 3.146,0.5 3.458,0.656 0.313,0.156 10 false *a 3.167,1.177 3.479,1.333 0.313,0.156 10 false *b 6.104,0.479 6.417,0.635 0.313,0.156 10 false *a 6.115,1.188 6.427,1.344 0.313,0.156 10 false *b
*A w/o Air Release Valve *B w/ Air Release Valve
*a FULL Line *b LOW Line


If the engine coolant level is low, check for leaks and add engine coolant to the FULL line.

NOTICE:

Do not substitute plain water for engine coolant.



Hide 3.INSPECT ENGINE COOLANT QUALITY (for Engine)

CAUTION:

Do not remove the reserve tank cap and air release valve (w/ air release valve) while the engine or radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.

Remove the reserve tank cap.


b.

Check if there are any excessive deposits of rust or scale around the reserve tank cap and radiator reserve tank filler hole. Also, the engine coolant should be free of oil.

If excessively dirty, clean the engine coolant passage and replace the engine coolant.


c.

Install the reserve tank cap.