Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3210E _59 Vehicle Exterior _047514 WIPER / WASHER _0233572 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 2.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

a.
E337211C01
1.99,0.792 2.458,0.875 true 2.479,0.771 2.677,0.969 0.198,0.198 10 true *a
*a Protective Tape


Using a screwdriver, disengage the 3 claws to remove the front wiper arm head cap.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side and LH side.




Hide 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E337213

Remove the nut and front wiper arm and blade assembly LH.


Hide 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E337215

Remove the nut and front wiper arm and blade assembly RH.


Hide 55754F 6.REMOVE COWL WATER EXTRACT SHIELD LH

a.
E337217C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides to remove the cowl water extract shield LH as shown in the illustration.


Hide 55753D 7.REMOVE COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.


Hide 55781E 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the 2 clips.

E337219


b.

Disengage the guide as shown in the illustration.

E337221


c.

Disengage the 3 guides and remove the cowl top ventilator louver sub-assembly as shown in the illustration.

E337225C01
2.708,2.292 2.875,2.094 false
V113147

Remove in this Direction - -


NOTICE:

When removing the cowl top ventilator louver sub-assembly, it may contact the brake master cylinder reservoir filler cap assembly and cause it to fall off. Check the installation condition of the brake master cylinder reservoir filler cap assembly after removing the cowl top ventilator louver sub-assembly.



Hide 9.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)

a.
E337229

Remove the 2 bolts.


b.
E337231C01
2.813,0.896 2.469,0.74 true 2.833,0.802 3.021,0.99 0.188,0.188 10 true *a
*a Motor Grommet


Disengage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when removing the windshield wiper motor and link assembly.



c.
E337235

Disconnect the connector to remove the windshield wiper motor and link assembly.


Hide 10.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

a.
E331313

Remove the 2 bolts.


b.
E331314C02
2.344,1.094 2.708,0.906 true 2.135,1 2.333,1.167 0.198,0.167 10 true *a
*a Motor Grommet


Disengage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when removing the windshield wiper motor and link assembly.



c.
E331316

Disconnect the connector to remove the windshield wiper motor and link assembly.


Hide 85012A 11.REMOVE FRONT WIPER CRANK SUB-ASSEMBLY (for RHD)

a.
E331317C02
1.75,1.823 1.646,1.229 true 0.563,1.281 1.021,1.177 false 1.708,1.833 2.021,2.031 0.313,0.198 10 false *a 0.365,1.198 0.677,1.396 0.313,0.198 10 false *b
*a Protective Tape
*b Pivot of Front Wiper Crank Sub-assembly


Using a screwdriver, separate the No. 1 windshield wiper link rod from the pivot of the front wiper crank sub-assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



b.
E331319C02
1.25,0.865 1.615,0.948 true 1.063,0.74 1.375,0.938 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, hold the front wiper crank sub-assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



c.

Remove the nut and front wiper crank sub-assembly.


Hide 85110 12.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E337237C01
1.844,1.844 2.104,1.271 true 2.104,0.854 2.375,0.677 false 1.76,1.854 2.073,2.052 0.313,0.198 10 false *a 2.396,0.552 2.708,0.75 0.313,0.198 10 false *b
*a Protective Tape
*b Pivot of Windshield Wiper Motor Assembly


Using a screwdriver, separate the No. 1 windshield wiper link rod from the pivot of the windshield wiper motor assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



b.
E337241

Remove the 3 bolts.


c.
E337243C01
1.865,1.792 1.979,1.792 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Move the windshield wiper motor assembly in the direction indicated by the arrow (1), then pull the windshield wiper motor assembly in the direction indicated by the arrow (2) shown in the illustration to remove it from the windshield wiper link assembly.


Hide 85110 13.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E331320

Remove the 3 bolts and windshield wiper motor assembly from the windshield wiper link assembly.