Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) U

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  TERMINALS OF ECM  


A335752E27
2.344,0.375 2.792,0.677 0.448,0.302 5.771,0.417 6.219,0.719 0.448,0.302 2.427,0.448 2.885,0.646 0.458,0.198 10 false C31 5.854,0.479 6.313,0.677 0.458,0.198 10 false A40

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-1 (BATT) - C31-59 (E1) B - W-B Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory) Power switch off 11 to 16 V
A40-2 (+B) - C31-59 (E1) R - W-B Power source of ECM Engine stopped, power switch on (IG) 11 to 14 V
A40-3 (+B2) - C31-59 (E1) R - W-B Power source of ECM Engine stopped, power switch on (IG) 11 to 14 V
A40-6 (IGSW) - C31-59 (E1) BE - W-B Power switch signal Engine stopped, power switch on (IG) 11 to 14 V
A40-7 (FANL) - C31-59 (E1) R - W-B Cooling fan motor operation signal (low) Power switch on (IG) 11 to 14 V
Idling, high engine coolant temperature Below 1.5 V
A40-8 (FANH) - C31-59 (E1) LG - W-B Cooling fan motor operation signal (high) Power switch on (IG) 11 to 14 V
Idling, high engine coolant temperature Below 1.5 V
A40-13 (CANH) - C31-59 (E1) R - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
A40-24 (LSTM) - C31-59 (E1) R - W-B Fuel lid operation signal for combination meter assembly Multi-information display displaying "Please Wait Now Opening" Pulse generation
(see waveform 2)
Multi-information display displaying "Close Fuel Lid" Pulse generation
(see waveform 3)
Multi-information display displaying "Refuel Ready" Pulse generation
(see waveform 4)
Power switch on (IG) 11 to 14 V
A40-26 (CANL) - C31-59 (E1) W - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 5)
A40-30 (NEO) - C31-59 (E1) L - W-B Crankshaft revolution signal Idling with warm engine Pulse generation
(See waveform 6)
A40-31 (TACH) - C31-59 (E1) V - W-B Engine speed signal Idling with warm engine Pulse generation
(See waveform 7)
A40-32 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A40-38 (MPMP) - A40-53 (EMPM) P - B Leak detection pump (canister pump module) signal Leak detection pump off Below 3.0 V
Leak detection pump on 9.0 to 14 V
A40-39 (VPMP) - C31-59 (E1) SB - W-B Vent valve (canister pump module) signal Power switch on (IG) 11 to 14 V
A40-40 (PPMP) - A40-54 (EPPM) W - LG Canister pressure sensor (canister pump module) signal Power switch on (IG) 3.0 to 3.6 V
A40-41 (FC) - C31-59 (E1) SB - W-B Fuel pump control Engine stopped, power switch on (IG) 11 to 14 V
Idling Below 1.5 V
A40-42 (FUEL) - C31-59 (E1) P - W-B Fuel lid opener switch signal Fuel lid opener switch pressed Below 1.0 V
Fuel lid opener switch not pressed 11 to 14 V
A40-43 (LIDO) - C31-59 (E1) GR - W-B Fuel lid courtesy switch signal Fuel lid closed Below 1.0 V
Fuel lid open 11 to 14 V
A40-46 (MREL) - C31-59 (E1) G - W-B EFI-MAIN relay operation signal Engine stopped, power switch on (IG) 11 to 14 V
A40-55 (VCPP) - A40-54 (EPPM) GR - LG Power source for canister pressure sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
A40-58 (CCV2) - C31-59 (E1) V - W-B Fuel vapor containment valve assembly signal Fuel vapor containment valve assembly on (open) Below 1.0 V
Fuel vapor containment valve assembly off (closed) 11 to 14 V
A40-59 (FREL) - C31-59 (E1) LG - W-B Fuel lid lock with motor assembly operation signal Fuel lid lock with motor assembly operating Below 1.0 V
Fuel lid lock with motor assembly not operating 11 to 14 V
C31-26 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C31-27 (HA1A) - C31-26 (E04) R - W-B Air fuel ratio sensor heater operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 8)
C31-28 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C31-29 (+BM) - C31-59 (E1) R - W-B Power source of throttle actuator Power switch off 11 to 16 V
C31-30 (M-) - C31-28 (ME01) P - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 9)
C31-31 (CAN+) - C31-59 (E1) SB - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
C31-32 (CAN-) - C31-59 (E1) W - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 5)
C31-33 (PRG) - C31-59 (E1) V - W-B Purge VSV operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 10)
C31-35 (OC1+) - C31-34 (OC1-) L - G Camshaft timing oil control valve assembly operation signal Idling Pulse generation
(See waveform 11)
C31-56 (HT1B) - C31-26 (E04) G - W-B Heated oxygen sensor heater operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with cold engine Below 3.0 V
C31-57 (E01) - Body ground W-B - - Ground Always Below 1 Ω
C31-58 (E02) - Body ground W-B - - Ground Always Below 1 Ω
C31-59 (E1) - Body ground W-B - - Ground Always Below 1 Ω
C31-60 (M+) - C31-28 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 12)
C31-68 (WPI) - C31-59 (E1) P - W-B Engine water pump assembly signal Idling with warm engine Pulse generation
(See waveform 13)
C31-69 (WPO) - C31-59 (E1) L - W-B Engine water pump assembly signal Idling with warm engine Pulse generation
(See waveform 14)
C31-70 (G2O) - C31-59 (E1) W - W-B Camshaft revolution signal Idling with warm engine Pulse generation
(See waveform 15)
C31-71 (IGF1) - C31-59 (E1) L - W-B Ignition coil assembly signal (ignition confirmation signal) Power switch on (IG) 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 16)
C31-72 (IGT4) - C31-59 (E1) V - W-B No. 4 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C31-73 (IGT3) - C31-59 (E1) G - W-B No. 3 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C31-74 (IGT2) - C31-59 (E1) B - W-B No. 2 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C31-75 (IGT1) - C31-59 (E1) GR - W-B No. 1 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 16)
C31-77 (VCPM) - C31-76 (EPIM) GR - V Power source of manifold absolute pressure sensor Engine stopped, power switch on (IG) 4.75 to 5.25 V
C31-78 (PIM) - C31-76 (EPIM) B - V Manifold absolute pressure sensor signal Engine stopped, power switch on (IG) 3.0 to 4.5 V
C31-82 (VV1+) - C31-115 (VV1-) SB - W Camshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 17)
C31-87 (THTW) - C31-88 (ETHT) SB - P No. 2 engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C31-92 (VPTK) - C31-91 (EPTK) L - V Power source of fuel tank pressure sensor (specific voltage) Engine stopped, power switch on (IG) 4.75 to 5.25 V
C31-93 (PTNK) - C31-91 (EPTK) G - V Fuel tank pressure sensor signal Engine stopped, power switch on (IG) 0.27 to 4.73 V
C31-95 (#20) - C31-57 (E01) LG - W-B No. 2 fuel injector assembly signal Idling with warm engine Pulse generation
(See waveform 18)
C31-96 (#30) - C31-57 (E01) L - W-B No. 3 fuel injector assembly signal Idling with warm engine Pulse generation
(See waveform 18)
C31-97 (#40) - C31-57 (E01) R - W-B No. 4 fuel injector assembly signal Idling with warm engine Pulse generation
(See waveform 18)
C31-98 (#10) - C31-57 (E01) BE - W-B No. 1 fuel injector assembly signal Idling with warm engine Pulse generation
(See waveform 18)
C31-99 (OX1B) - C31-131 (EX1B) V - P Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 19)
C31-100 (A1A+) - C31-59 (E1) Y - W-B Air fuel ratio sensor signal Engine stopped, power switch on (IG) 3.0 to 3.6 V*
C31-101 (VTA2) - C31-133 (ETA) B - G Throttle position sensor signal (for sensor malfunction detection) Engine stopped, power switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
C31-105 (EGR4) - C31-59 (E1) LG - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 20)
C31-106 (EGR2) - C31-59 (E1) R - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 20)
C31-107 (EGR3) - C31-59 (E1) BE - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 20)
C31-108 (GE01) - Body ground L - - Shielded (ground) circuit of throttle actuator Always Below 1 Ω
C31-114 (NE+) - C31-113 (NE-) B - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 21)
C31-116 (VCV1) - C31-59 (E1) R - W-B Power source of camshaft position sensor Engine stopped, power switch on (IG) 4.5 to 5.5 V
C31-120 (THW) - C31-119 (ETHW) L - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C31-122 (KNK1) - C31-121 (EKNK) B - W Knock control sensor signal Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(See waveform 22)
C31-132 (A1A-) - C31-59 (E1) BR - W-B Air fuel ratio sensor signal Engine stopped, power switch on (IG) 2.7 to 3.3 V*
C31-134 (VCTA) - C31-133 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine stopped, power switch on (IG) 4.5 to 5.5 V
C31-135 (VTA1) - C31-133 (ETA) BE - G Throttle position sensor signal (for engine control) Engine stopped, power switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
C31-137 (VG) - C31-104 (E2G) G - L Mass air flow meter sub-assembly signal Idling, park (P) or neutral (N) selected, A/C switch off 0.5 to 3.0 V
C31-138 (THA) - C31-139 (ETHA) V - GR Intake air temperature sensor (mass air flow meter sub-assembly) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C31-140 (EGR1) - C31-59 (E1) P - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 20)

*: The ECM terminal voltage is constant regardless of the voltage output from the sensor.

WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CAN+ and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A375176E01
2.667,0.115 3.25,0.302 0.583,0.188 10 false 5 V/DIV. 2.771,0.948 3.354,1.135 0.583,0.188 10 false GND 1.344,1.927 2.115,2.125 0.771,0.198 10 false 20 ms./DIV.

Fuel Lid Operation Signal for Combination Meter Assembly
ECM Terminal Name Between LSTM and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Multi-information display displaying "Please Wait Now Opening"


WAVEFORM 3


A375177E01
2.688,0.094 3.24,0.302 0.552,0.208 10 false 5 V/DIV. 2.771,0.938 3.323,1.146 0.552,0.208 10 false GND 1.302,1.896 2.052,2.063 0.75,0.167 10 false 20 ms./DIV.

Fuel Lid Operation Signal for Combination Meter Assembly
ECM Terminal Name Between LSTM and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Multi-information display displaying "Close Fuel Lid"


WAVEFORM 4


A375178E01
2.667,0.094 3.24,0.292 0.573,0.198 10 false 5 V/DIV. 2.76,0.927 3.333,1.125 0.573,0.198 10 false GND 1.313,1.906 2.104,2.073 0.792,0.167 10 false 20 ms./DIV.

Fuel Lid Operation Signal for Combination Meter Assembly
ECM Terminal Name Between LSTM and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Multi-information display displaying "Refuel Ready"


WAVEFORM 5


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CAN- and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 6


A214025E27
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Crankshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 7


A287797E06
2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.646,0.115 3.26,0.302 0.615,0.188 10 false 5 V/DIV. 2.615,1.927 3.396,2.094 0.781,0.167 10 false 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 9


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 10


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 12


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 13


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 14


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 15


A214025E25
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Camshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between G2O and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 16


A289263E05
2.844,0.854 3.208,1.052 0.365,0.198 10 false GND 2.844,1.5 3.177,1.698 0.333,0.198 10 false GND 0.042,0.417 0.365,0.927 0.323,0.51 10 false CH1 (IGT) 0.021,1.198 0.406,1.823 0.385,0.625 10 false CH2 (IGF1) 0.031,0.031 0.573,0.208 0.542,0.177 10 false 2 V/DIV. 1.156,1.844 1.906,1.99 0.75,0.146 10 false 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A254147E02
2.986,0.993 3.323,1.140 0.336,0.147 10 GND 1.159,1.916 1.902,2.062 0.744,0.147 10 20 ms./DIV. 2.748,0.059 3.284,0.206 0.536,0.147 10 5 V/DIV.

Camshaft Position Sensor Signal
ECM Terminal Name Between VV1+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

No. 1 (to No. 4) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List item "O2 Sensor Voltage B1S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 20


A214026E05
2.849,2.294 3.179,2.450 0.330,0.156 10 GND 2.849,1.922 3.179,2.077 0.330,0.156 10 GND 2.849,1.578 3.179,1.734 0.330,0.156 10 GND 2.849,1.24 3.179,1.396 0.330,0.156 10 GND 0.235,1.039 0.686,1.195 0.451,0.156 10 EGR1 0.235,1.405 0.686,1.560 0.451,0.156 10 EGR2 0.235,1.757 0.686,1.913 0.451,0.156 10 EGR3 0.235,2.113 0.686,2.269 0.451,0.156 10 EGR4 1.248,2.42 1.997,2.577 0.749,0.157 10 50 ms./DIV. 1.979,0.406 2.643,0.581 0.665,0.175 10 20 V/DIV.

EGR Valve Assembly Signal
ECM Terminal Name Between EGR (1 to 4) and E1
Tester Range 20 V/DIV., 50 ms./DIV.
Condition EGR valve assembly operating


WAVEFORM 21


A254145E10
2.984,0.964 3.337,1.167 0.353,0.202 10 GND 0.067,0.058 0.612,0.235 0.545,0.177 10 5 V/DIV. 1.22,1.917 1.972,2.062 0.751,0.145 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 22


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.