Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P01102A  Intake Air Temperature Sensor 1 Bank 1 Signal Stuck in Range  


DESCRIPTION

Refer to DTC P011011.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P011011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P01102A Intake Air Temperature Sensor 1 Bank 1 Signal Stuck in Range Either of the following conditions is met (2 trip detection logic).
·

The intake air temperature change from the previous trip warm up to the following trip is small.

·

The change in the intake air temperature after engine start is less than the threshold value.


Mass air flow meter sub-assembly Comes on DTC stored SAE Code: P0111

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor (mass air flow meter sub-assembly). If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that the sensor is malfunctioning. The ECM detects when the intake air temperature sensor value is stuck by performing monitoring after the power switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A198822E39
2.24,2.948 2.802,3.333 0.563,0.385 10 false Warming up 2.896,2.958 4.292,3.406 1.396,0.448 10 false 5 minutes or more 2.021,2.094 2.396,2.406 0.375,0.313 10 false [A] 2.51,1.813 2.969,2.208 0.458,0.396 10 false [B] 3.354,1.792 3.719,2.146 0.365,0.354 10 false [C] 3.99,3.156 4.375,3.5 0.385,0.344 10 false [D] 0.573,1.083 1.604,1.542 1.031,0.458 10 false 40 km/h [Engine running] 1.302,1.938 1.844,2.219 0.542,0.281 10 false Idling 0.354,2.24 1.75,2.49 1.396,0.25 10 false Power Switch on (IG) 4.146,0.313 5.854,0.646 1.708,0.333 10 false Total of 5 minutes or more 4.802,0.729 5.167,1.042 0.365,0.313 10 false [E] 6.146,3.396 6.563,3.802 0.417,0.406 10 false [F]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

10.

Idle the engine for 5 minutes or more [C].

HINT:

During steps [A] through [C], if the change in the intake air temperature is less than 1°C (2°F), the intake air temperature sensor (mass air flow meter sub-assembly) is malfunctioning. It is not necessary to continue this procedure.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P01102A.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [E] and [F].



16.

With the engine running, drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


17.

Check the DTC judgment result again [F].

HINT:

If the judgment result is INCOMPLETE or N/A, perform steps [E] and [F] again.



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P01102A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P01102A and other DTCs are output A
DTC P01102A is output B


HINT:
·

If any DTCs other than P01102A are output, troubleshoot those DTCs first.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





A

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY