Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P142000  Evaporative Emission Canister (Small Leak)  P142100  Evaporative Emission Canister (Gross Leak)  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P142000 Evaporative Emission Canister (Small Leak) Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure is measured at the start and at the end of leak check. If stabilized pressure is higher than second reference pressure, ECM determines that EVAP system has a small leak.
·

EVAP leak (purge VSV - canister - fuel vapor-containment valve)

·

Purge VSV

·

Connector/wire harness (purge VSV - ECM)

·

Canister pump module

·

ECM


Comes on DTC stored SAE Code: P1420
P142100 Evaporative Emission Canister (Gross Leak) Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure is measured at the start and at the end of leak check. If stabilized pressure is higher than [second reference pressure x 0.2], ECM determines that EVAP system has a large leak.
·

EVAP leak (purge VSV - canister - fuel vapor-containment valve)

·

Purge VSV

·

Connector/wire harness (purge VSV - ECM)

·

Canister pump module

·

ECM


Comes on DTC stored SAE Code: P1421

DTC No. Monitoring Item Detection Timing Detection Logic SAE Code
P142000 Canister small leak EVAP monitoring
(Power switch off)
2 trip P1420
P142100 Canister gross leak P1421

DESCRIPTION

The description can be found in the EVAP (evaporative emission) System.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>EVAP System

MONITOR DESCRIPTION

1.

P142000: EVAP (evaporative emission) small leak

In operation C, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than the second reference pressure, the ECM determines that the EVAP system has a small leak, illuminates the MIL and stores the DTC (2 trip detection logic).

2.

P142100: EVAP gross leak

In operation C, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than [second reference pressure x 0.2] (near atmospheric pressure), the ECM determines that the EVAP system has a large leak, illuminates the MIL and stores the DTC (2 trip detection logic).


A319538E01
2.802,5.563 3,5.563 3,5.563 3.073,5.417 false 4.792,5.375 4.875,5.615 4.875,5.615 4.979,5.615 false 4.563,5.01 4.708,5.219 4.708,5.219 4.854,5.219 false 3.51,4.469 3.323,4.469 3.323,4.469 3.031,5.156 false 2.438,4.521 2.625,4.521 2.625,4.521 2.802,4.875 false 2.802,3.396 2.542,3.396 2.542,3.396 1.99,4.24 false 2.5,3.698 2.698,3.396 false 4.75,2.781 4.896,2.781 4.896,2.781 5.115,3.104 false 3.948,2 3.76,2 3.76,2 3.594,2.354 false 4.438,1.063 4.25,1.063 4.25,1.063 4.188,0.854 false 4.094,0.292 3.938,0.292 3.938,0.292 3.635,0.708 false 0.24,0.094 1.125,0.417 0.885,0.323 10 false Method A 0.635,0.667 1.323,1.25 0.688,0.583 10 false Vent Valve (Switching Valve) 0.333,1.458 1.271,2.021 0.938,0.563 10 false Leak Detection Pump 0.615,2.396 1.396,2.76 0.781,0.365 10 false Purge VSV 0.5,3.094 1.26,3.646 0.76,0.552 10 false Fuel Vapor-containment Valve 0.104,3.938 2.063,4.281 1.958,0.344 10 false Fuel Tank Pressure 0.344,4.75 1.427,5.156 1.083,0.406 10 false EVAP Pressure 0.458,5.229 1.323,5.708 0.865,0.479 10 false 1st Reference Pressure 0.677,6.042 1.76,6.448 1.083,0.406 10 false Sequence 1.01,6.354 2.094,6.76 1.083,0.406 10 false Time 1.188,6.615 2.271,7.021 1.083,0.406 10 false 60 seconds 1.698,6.823 2.781,7.229 1.083,0.406 10 false 360 seconds 2.479,6.625 3.958,6.875 1.479,0.25 10 false Within 15 minutes 3.375,6.833 4.198,7.125 0.823,0.292 10 false 10 seconds 3.906,6.625 4.729,6.917 0.823,0.292 10 false 60 seconds 4.344,6.844 5.167,7.135 0.823,0.292 10 false 5 seconds 4.854,6.625 5.677,6.917 0.823,0.292 10 false 0.1 seconds 5.74,4.792 7.135,5.063 1.396,0.271 10 false Atmospheric Pressure 5.74,3.906 7.135,4.177 1.396,0.271 10 false Atmospheric Pressure 2.563,5.49 2.844,5.708 0.281,0.219 10 false OK 5.021,5.51 5.313,5.76 0.292,0.25 10 false *1 4.875,5.125 5.167,5.375 0.292,0.25 10 false *2 3.552,4.365 4.271,4.708 0.719,0.344 10 true Malfunction 1.708,4.417 2.427,4.76 0.719,0.344 10 true Malfunction 2.885,3.313 4.094,3.635 1.208,0.323 10 true Fuel Tank Pressure 4.073,2.667 4.698,3.021 0.625,0.354 10 true ON: Open 4,1.927 4.625,2.281 0.625,0.354 10 true ON: Open 2.865,0.76 3.094,1.01 0.229,0.25 10 true ON 2.865,1.479 3.094,1.729 0.229,0.25 10 true ON 4.156,0.198 4.813,0.51 0.656,0.313 10 true ON: Close 4.5,0.99 5.177,1.302 0.677,0.313 10 true OFF: Vent 4.885,0.76 5.125,0.927 0.24,0.167 10 true ON 1.948,7.406 2.458,7.604 0.51,0.198 10 false : OK 2.823,7.406 3.969,7.635 1.146,0.229 10 false : Malfunction 4.396,7.198 6.469,7.458 2.073,0.26 10 false *1: Second Reference Pressure 4.396,7.521 6.885,7.781 2.49,0.26 10 false *2: (Second Reference Pressure) x 0.2 1.521,5.917 1.74,6.188 0.219,0.271 10 false A 2.042,5.917 2.26,6.188 0.219,0.271 10 false B 2.917,5.917 3.135,6.188 0.219,0.271 10 false C 3.656,5.917 3.875,6.188 0.219,0.271 10 false D 4.177,5.917 4.396,6.188 0.219,0.271 10 false E 4.635,5.917 4.854,6.188 0.219,0.271 10 false F 5.094,5.917 5.313,6.188 0.219,0.271 10 false I 3.583,2.438 3.813,2.688 0.229,0.25 10 true ON 5.021,3.24 5.25,3.49 0.229,0.25 10 false ON

A319539E01
2.583,1.021 2.698,0.729 2.698,0.729 2.865,0.729 false 4.49,1.177 4.823,1.49 4.823,1.49 4.979,1.49 false 3.594,2.698 3.854,2.323 3.854,2.323 4.01,2.323 false 4.813,3.385 5,3.073 5,3.073 5.135,3.073 false 4.75,4.333 4.885,3.948 4.885,3.948 5.406,3.948 false 4.802,5.115 5.188,3.948 false 2.708,5.344 2.875,4.521 2.875,4.521 3.083,4.521 false 2.594,5.104 2.302,4.708 2.302,4.708 2.115,4.708 false 2.917,5.635 2.833,5.802 2.833,5.802 2.667,5.802 false 4.76,5.531 4.677,5.531 4.677,5.531 4.427,5.198 false 4.906,5.885 4.823,5.885 4.823,5.885 4.656,5.635 false 0.198,0.198 0.875,0.49 0.677,0.292 10 false Method B 0.563,1 1.271,1.615 0.708,0.615 10 false Vent Valve (Switching Valve) 0.333,1.896 1.302,2.344 0.969,0.448 10 false Leak Detection Pump 0.563,2.75 1.531,3.198 0.969,0.448 10 false Purge VSV 0.521,3.354 1.302,3.958 0.781,0.604 10 false Fuel Vapor-containment Valve 0.094,4.24 1.354,4.635 1.26,0.396 10 false Fuel Tank Pressure 0.313,5.052 1.313,5.427 1,0.375 10 false EVAP Pressure 0.656,5.781 1.333,6.115 0.677,0.333 10 false Sequence 0.969,6.344 1.375,6.594 0.406,0.25 10 false Time 1.135,6.677 2.063,6.906 0.927,0.229 10 false 60 seconds 1.708,6.938 2.635,7.167 0.927,0.229 10 false 360 seconds 2.385,6.656 3.594,6.896 1.208,0.24 10 false Within 15 minutes 3.229,6.896 4.083,7.146 0.854,0.25 10 false 10 seconds 3.729,6.667 4.583,6.917 0.854,0.25 10 false 60 seconds 4.76,6.688 5.979,6.938 1.219,0.25 10 false Within 15 minutes 5.813,6.875 6.594,7.125 0.781,0.25 10 false 60 seconds 1.844,7.427 2.25,7.656 0.406,0.229 10 false : OK 2.719,7.438 3.635,7.667 0.917,0.229 10 false : Malfunction 4.552,7.198 6.656,7.406 2.104,0.208 10 false *1: Second Reference Pressure 4.531,7.521 6.979,7.75 2.448,0.229 10 false *2: (Second Reference Pressure) x 0.2 1.469,5.917 1.719,6.135 0.25,0.219 10 false A 2.021,5.917 2.271,6.135 0.25,0.219 10 false B 2.885,5.917 3.135,6.135 0.25,0.219 10 false C 3.563,5.917 3.781,6.146 0.219,0.229 10 false D 4.073,5.917 4.292,6.146 0.219,0.229 10 false E 4.51,5.917 4.729,6.146 0.219,0.229 10 false F 5.219,5.917 5.438,6.146 0.219,0.229 10 false G 6.146,5.917 6.365,6.146 0.219,0.229 10 false H 2.448,5.708 2.698,5.927 0.25,0.219 10 false OK 4.927,5.771 5.177,5.99 0.25,0.219 10 false *1 4.781,5.427 5.031,5.646 0.25,0.219 10 false *2 3.146,4.438 3.865,4.76 0.719,0.323 10 true Malfunction 1.385,4.625 2.104,4.948 0.719,0.323 10 true Malfunction 5.479,3.865 6.865,4.271 1.385,0.406 10 true Atmospheric Pressure 4.073,2.229 4.698,2.604 0.625,0.375 10 true ON: Open 5.198,3 5.844,3.323 0.646,0.323 10 true ON: Open 5.156,3.406 5.427,3.646 0.271,0.24 10 false ON 3.51,2.76 3.781,3 0.271,0.24 10 true ON 5.177,1.917 5.448,2.156 0.271,0.24 10 true ON 5.146,1.104 5.417,1.344 0.271,0.24 10 true ON 2.802,1.917 3.073,2.156 0.271,0.24 10 true ON 2.813,1.094 3.083,1.333 0.271,0.24 10 true ON 2.948,0.667 3.667,0.979 0.719,0.313 10 true ON: Close 5.031,1.406 5.75,1.75 0.719,0.344 10 true OFF: Vent 4.177,6.896 5.031,7.146 0.854,0.25 10 false 5 seconds

MONITOR STRATEGY

Required Sensors/Components Purge VSV
Canister pump module
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 9 steps performed automatically by the GTS. It takes a maximum of approximately 40 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not start the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor will from and any check result will be inaccurate. When performing the Evaporative System Check, keep the fuel temperature less than 35°C (95°F).



1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.

9.

After the "Evaporative System Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P142000 or P142100.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




PROCEDURE

1.GO TO EVAP SYSTEM

NEXT

END