Home › Vehicle Interior › LIGHTING (INT) › PERSONAL LIGHT
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0236238 PERSONAL LIGHT G

LIGHTING (INT)  PERSONAL LIGHT  INSPECTION  


PROCEDURE

Hide 81260A 1.INSPECT MAP LIGHT ASSEMBLY (w/o Sliding Roof)

a.
E336493C01
0.521,0.563 0.948,1.177 false 1.188,1.333 0.823,1.771 false 1.448,1.385 1.24,1.76 false 2.115,0.521 1.667,1.177 false 2.083,1.396 2.396,1.708 false 2.938,0.521 2.563,1.177 false 2.875,0.313 3.333,0.51 0.458,0.198 10 false +B1 0.177,0.406 0.635,0.604 0.458,0.198 10 false GND9 1.958,0.323 2.531,0.552 0.573,0.229 10 false RLMP 2.385,1.771 2.844,1.969 0.458,0.198 10 false ILLB 1.177,1.833 1.635,2.031 0.458,0.198 10 false LILL 0.563,1.813 1.021,2.01 0.458,0.198 10 false DOOR 0.083,0.094 0.479,0.292 0.396,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Inspect the map light.

i.

Apply auxiliary battery voltage to the connector and check that the map light comes on.

Result:
Connection Condition Specified Condition
Auxiliary battery positive (+) → 1 (+B1)
Auxiliary battery negative (-) → 8 (GND9)
Front map light switches off and interior light door switch on Front map light LH and RH come on
Front map light switch LH on Front map light LH comes on
Front map light switch RH on Front map light RH comes on
Auxiliary battery positive (+) → 1 (+B1)
Auxiliary battery negative (-) → 7 (DOOR)
Front map light switches off and interior light door switch DOOR Front map light LH and RH come on


If the result is not as specified, replace the bulb or map light assembly.



b.

Inspect the interior light door switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLMP) - 7 (DOOR) Interior light door switch DOOR Below 1 Ω
5 (RLMP) - 8 (GND9) Interior light door switch on Below 1 Ω


If the result is not as specified, replace the map light assembly.



c.

Inspect the switch illumination.

i.

Apply auxiliary battery voltage to the connector and check that the switch illumination comes on.

OK:
Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → 3 (ILLB)
Auxiliary battery negative (-) → 6 (LILL)
Always Switch illumination comes on


If the result is not as specified, replace the map light assembly.



Hide 81260A 2.INSPECT MAP LIGHT ASSEMBLY (w/ Sliding Roof)

a.
B356073C05
2.281,1.24 2.781,0.625 false 2.292,1.448 2.583,1.802 false 2.031,1.427 1.99,1.76 false 2.125,0.667 2.104,1.219 false 1.198,0.635 1.406,1.208 false 0.479,1.615 1.156,1.26 false 0.167,0.167 0.333,0.333 0.167,0.167 10 false *a 0.281,1.677 0.74,1.875 0.458,0.198 10 false +B1 2.646,1.833 3.104,2.031 0.458,0.198 10 false GND 1.948,0.448 2.406,0.646 0.458,0.198 10 false RLMP 1.063,0.448 1.521,0.646 0.458,0.198 10 false ILLB 1.906,1.854 2.365,2.052 0.458,0.198 10 false LILL 2.615,0.438 3.073,0.635 0.458,0.198 10 false DOOR
*a Component without harness connected
(Map Light Assembly)


Inspect the map light.

i.

Apply auxiliary battery voltage to the connector and check that the map light comes on.

Result:
Connection Condition Specified Condition
Auxiliary battery positive (+) → 10 (+B1)
Auxiliary battery negative (-) → 11 (GND)
Front map light switches off and interior light ON/OFF switch on Front map light LH and RH come on
Front map light switch LH on Front map light LH comes on
Front map light switch RH on Front map light RH comes on
Auxiliary battery positive (+) → 10 (+B1)
Auxiliary battery negative (-) → 1 (DOOR)
Front map light switches off and interior light door switch on Front map light LH and RH come on


If the result is not as specified, replace the bulb or map light assembly.



b.

Inspect the interior light door switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RLMP) - 1 (DOOR) Interior light door switch on Below 1 Ω


If the result is not as specified, replace the map light assembly.



c.

Inspect the switch illumination.

i.

Apply auxiliary battery voltage to the connector and check that the switch illumination comes on.

OK:
Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → 8 (ILLB)
Auxiliary battery negative (-) → 13 (LILL)
Always Switch illumination comes on


If the result is not as specified, replace the map light assembly.