Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM3210E _54 Brake _047520 BRAKE (FRONT) _0237141 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REASSEMBLY  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 47547B 1.TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG

HINT:

Fully tighten the front disc brake bleeder plug after bleeding the system.


Hide 31478B 2.INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.
C344530C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the entire circumference of a new piston seal.


b.
C344531C02
0.75,0.896 0.885,0.573 0.885,0.573 0.969,0.573 false 0.927,1.063 1.073,1.063 false 1.115,1 1.427,1.156 0.313,0.156 10 false *1 1.01,0.51 1.323,0.667 0.313,0.156 10 false *2
*1 Piston Seal
*2 Front Disc Brake Cylinder


Install the piston seal to the front disc brake cylinder.

NOTICE:

Securely install the piston seal into the groove of the front disc brake cylinder.



Hide 47731 4.INSTALL FRONT DISC BRAKE PISTON

a.
C344532C02
2.26,0.5 2.76,0.5 false 2.146,1.604 2.719,1.604 false 2.802,0.438 3.115,0.594 0.313,0.156 10 false *1 2.76,1.542 3.073,1.698 0.313,0.156 10 false *2
*1 Cylinder Boot
*2 Front Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.


b.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the front disc brake piston.


c.

Install the cylinder boot to the front disc brake piston.

NOTICE:

Securely install the cylinder boot into the groove of the front disc brake piston.



d.
C344533C02
0.979,0.479 1.073,0.479 1.073,0.479 1.208,0.615 false 0.344,1.521 0.344,1.385 0.344,1.385 0.521,1.385 false 1.115,1.344 1.115,0.969 false 0.5,0.49 0.667,0.49 0.667,0.49 0.667,0.896 true 1.063,1.375 1.375,1.531 0.313,0.156 10 false *1 0.802,0.417 1.115,0.573 0.313,0.156 10 false *2 0.281,1.542 0.594,1.698 0.313,0.156 10 false *3 0.323,0.427 0.635,0.583 0.313,0.156 10 false *4
*1 Cylinder Boot
*2 Front Disc Brake Piston
*3 Front Disc Brake Cylinder
*4 Set Ring


Install the front disc brake piston to the front disc brake cylinder.

NOTICE:

Do not forcibly install the front disc brake piston into the front disc brake cylinder.



e.

Install the cylinder boot to the front disc brake cylinder as shown in the illustration.

NOTICE:
·

Securely install the cylinder boot into the groove of the front disc brake cylinder.

·

Do not damage the cylinder boot.




f.
C344516C03
1.823,1.198 2.49,1.656 2.49,1.656 2.604,1.656 false 2.646,1.594 2.958,1.75 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, install a new set ring.

NOTICE:

Do not damage the cylinder boot.