Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM
RM3210E _59 Vehicle Exterior _047541 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0237698 VEHICLE PROXIMITY NOTIFICATION SYSTEM U

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch signal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Operation Cancel SW Pattern select switch assembly (vehicle approaching speaker switch) signal OFF or ON OFF: Pattern select switch assembly (vehicle approaching speaker switch) is not pressed.
ON: Pattern select switch assembly (vehicle approaching speaker switch) is pressed.
-
IG2 IG signal OFF or ON OFF: Power switch off
ON: Power switch on (IG)
-
Ready Signal Ready signal OFF or ON OFF: Power switch off
ON: Power switch on (Ready)
-
Dimming Request Status of Proximity Sound Indicator Illumination dimming status of the indicator light Indeterminacy / Non-dimming / Dimming Indeterminacy: No automatic light control sensor signal
Non-dimming: Automatic light control sensor daytime signal
Dimming: Automatic light control sensor nighttime signal
-
Engine Mode Status of the engine Stopped / Move to Stopping / Starting / Running Displays current engine status -
Shift Switch Status Shift position signal P Range / R Range / N Range / D Range / B Range Displays current shift status -
HV Motor Rotational Speed RPM of the HV motor -10000 to 10000 [rpm] Displays current HV motor RPM -
Vehicle Speed Vehicle speed signal -327.68 to 327.67 [km/h] Displays current vehicle speed -
Vehicle Speed Signal Status Whether the Vehicle speed is within the vehicle proximity notification system operation range. Available / Not Available Available: Vehicle speed within operation range
Not Available: Vehicle speed not within operation range
-
AD Voltage of Speaker Abnormal Open or short in speaker circuit 0 to 5 [V] 0 V: Open
5 V: Short
-
Voltage of Amplifier Circuit Input voltage 0 to 20 [V] Current input voltage -
Proximity Sound Volume Adjustment Warning sound volume setting Standard, Standard +1, Standard +2 Customized value displayed -
Proximity Sound Level Increase (Vehicle Starting) Warning sound amplifier function when vehicle starts off OFF or ON Customized value displayed -
Proximity Sound Control (Vehicle Stationary) Warning sound setting function when vehicle stopped OFF or ON Customized value displayed -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound Indicator Proximity sound indicator OFF or ON -
Proximity Sound (Vehicle Stationary) Proximity sound (Vehicle stationary) OFF or ON Produces warning sound when vehicle is stopped
Proximity Sound (Low Speed) Proximity sound (Low speed) OFF or ON Produces warning sound when vehicle is being driven at speeds of 10 km/h (6 mph)