DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Power switch | ON or OFF | ON: Power switch on (ACC)
OFF: Power switch off |
- |
| IG SW | Power switch | ON or OFF | ON: Power switch on (IG)
OFF: Power switch off or on (ACC) |
- |
| RR Door Courtesy SW | Rear door courtesy light switch assembly (for RH) | ON or OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch assembly (for LH) | ON or OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| Back Door Courtesy SW | Back door courtesy light switch | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
| FR Door Lock Pos | Front door RH unlock detection switch | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FR Door Courtesy SW | Front door courtesy light switch assembly (for RH) | ON or OFF | ON: Front door RH open
OFF: Front door RH closed |
- |
| FL Door Lock Pos | Front door LH unlock detection switch | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| FL Door Courtesy SW | Front door courtesy light switch assembly (for LH) | ON or OFF | ON: Front door LH open
OFF: Front door LH closed |
- |
| Hood Courtesy SW | Engine hood courtesy switch | ON or OFF | ON: Engine hood open
OFF: Engine hood closed |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch | ON or OFF | ON: Rear door RH unlocked
OFF: Rear door RH locked |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch | ON or OFF | ON: Rear door LH unlocked
OFF: Rear door LH locked |
- |
| Glass Break Sensor Detection | Glass breakage sensor breakage detection*1 | ON or OFF | ON: Glass breakage sensor breakage detected
OFF: Glass breakage sensor breakage not detected |
- |
| Intrusion Sensor | Detection status of the intrusion sensor (theft warning ultrasonic sensor)*1 | ON or OFF | ON: Intrusion detected
OFF: Intrusion not detected |
- |
| Intrusion Sen Conn | Intrusion sensor (theft warning ultrasonic sensor) connection*1 | ON or OFF | ON: Intrusion sensor connected
OFF: Intrusion sensor not connected |
- |
| Sealed Glas Brak Sen | Glass breakage sensor connection*1 | With or Without | With: Glass breakage sensor connected
Without: Glass breakage sensor not connected |
- |
| Intrusion Sensor Sound Detect | Sound detection status of the intrusion sensor (theft warning ultrasonic sensor)*4 | ON or OFF | ON: Sound detected
OFF: Sound not detected |
Not applicable |
| Panic Function | Setting of customize setting "Panic Function"*2 | ON or OFF | Customize setting displayed | - |
| Intrusion Win Opened | Setting of customize setting "Intrusion Win Opened"*1 | ON or OFF | Customize setting displayed | - |
| Security control with mechanism key | Setting of customize setting "Security control with mechanism key"*3 | ON or OFF | Customize setting displayed | - |
| Communication Theft Deterrent | Connection status between theft deterrent ECU and main body ECU (multiplex network body ECU)*4 | STOP or OK | STOP: Communication stopped
OK: Normal communication |
Not applicable |
| The Number of DTC | Number of DTCs | 0 to 255 | Number of DTCs will be displayed | - |
*1: w/ Intrusion Sensor
*2: w/ Panic Switch
*3: Vehicles displaying the item "Security control with mechanism key" on the GTS
*4: Although the item is displayed on the GTS, it is not applicable to this vehicle.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body or Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Horn2 | Theft warning siren assembly*2 | OFF/ON | - |
| Vehicle Horn | Vehicle horns | OFF/ON | - |
| Security Horn | Security horn assembly*1 | OFF/ON | - |
| Power For Intrusion Sensor | Intrusion sensor (theft warning ultrasonic sensor) power supply*3 | OFF/ON | - |
*1: w/ Security Horn Assembly
*2: w/o Security Horn Assembly
*3: w/ Intrusion Sensor
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Immobiliser Indicator | Security indicator | OFF/ON | - |