Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0239264 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the O7 forward recognition camera connector.



E256359E48
2.146,0.76 2.5,1 0.354,0.24 2.198,0.802 2.656,1 0.458,0.198 10 false O7

a.

Disconnect the O7 forward recognition camera connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O7-7 (IGB) - O7-10 (GND) LG - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
O7-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O7 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O7-5 (CA1P) - O7-10 (GND) GR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
O7-11 (CA1N) - O7-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
O7-6 (CANH) - O7-10 (GND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
O7-12 (CANL) - O7-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between O7-5 (CA1P) and O7-10 (GND)
Between O7-6 (CANH) and O7-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between O7-11 (CA1N) and O7-10 (GND)
Between O7-12 (CANL) and O7-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.