Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781E26
3.396,0.115 3.833,0.354 0.438,0.24 3.5,0.156 4.115,0.354 0.615,0.198 10 false F40

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

F40-7 (B) - F40-28 (GND) P - W-B *1
B - W-B *2
Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
F40-3 (BZ) - F40-28 (GND) P - W-B Skid control buzzer output Power switch on (IG), buzzer not sounding 11 to 14 V
Power switch on (IG), buzzer sounding Below 1 V
F40-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F40-8 (CA1P) - F40-28 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
F40-9 (CA1N) - F40-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
F40-10 (CA2H) - F40-28 (GND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
F40-11 (CA2L) - F40-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between F40-8 (CA1P) - F40-28 (GND)
Between F40-10 (CA2H) - F40-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between F40-9 (CA1N) - F40-28 (GND)
Between F40-11 (CA2L) - F40-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


E321782E17
2.167,0.75 2.583,1 0.417,0.25 2.292,0.792 2.75,0.99 0.458,0.198 10 false A2

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-8 (IGB) - A2-1 (SGND) LG - W-B Power source Power switch on (IG) 11 to 14 V
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the millimeter wave radar sensor is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-3 (CA2H) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-2 (CA2L) - A2-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-5 (CA1P) - A2-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-6 (CA1N) - A2-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between A2-3 (CA2H) and A2-1 (SGND)
Between A2-5 (CA1P) and A2-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between A2-2 (CA2L) and A2-1 (SGND)
Between A2-6 (CA1N) and A2-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.