The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.
Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly sends pre-crash safety system control operation signals.
When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor, etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated. If the millimeter wave radar sensor assembly beam axis has deviated, the driving support ECU assembly detects this and stores DTC C1A11.
After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment has not been performed, DTC C1A14 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A11 | Front Radar Sensor Incorrect Axial Gap | When the power switch is on (IG), misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds. | ·
Millimeter wave radar sensor assembly ·
Driving support ECU assembly |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted | When the vehicle is being driven at a speed of 10 km/h (7 mph) or more, incompletion of the millimeter wave radar sensor beam axis alignment is detected for approximately 0.2 seconds. | ·
Millimeter wave radar sensor assembly ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Current DTC C1A11 is output | A |
| Current DTC C1A14 is output | B |
| History DTC C1A11 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or has been towed. | A |
| Vehicle is overloaded or has been towed. | B |
A
B
Check the front and rear wheel alignment (toe).
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the driving support ECU assembly.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 0.2 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
When the bracket is deformed, replace the millimeter wave radar sensor assembly.
The bracket is not deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 0.2 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the driving support ECU assembly.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Drive the vehicle at a speed of 10 km/h (7 mph) or more for 0.2 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A14 is not output | A |
| DTC C1A14 is output | B |
A
B
Check for DTCs related to misalignment of millimeter wave radar sensor assembly.
If only history DTCs are stored, they may have been stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT