Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A63  Accelerator Pedal Position Sensor Circuit  


DESCRIPTION

The driving support ECU assembly receives accelerator pedal position sensor signals from the hybrid vehicle control ECU to determine if the accelerator pedal is being depressed. If the hybrid vehicle control ECU detects a malfunction in the accelerator pedal position sensor or hybrid control system, the driving support ECU assembly is notified via CAN communication and stores DTC C1A63.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A63 Accelerator Pedal Position Sensor Circuit While the power switch is on (IG), the driving support ECU assembly receives a malfunction signal from the hybrid vehicle control ECU continuously for approximately 1.3 seconds or more.
HINT:

Even when there is no malfunction in the hybrid control system, if there is a malfunction in the motor generator control system, SFI system or hybrid battery system, the driving support ECU assembly receives a malfunction signal from the hybrid vehicle control ECU.


·

Hybrid control system

·

Motor generator control system

·

SFI system

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs
HINT:

Pre-crash safety system DTC C1A63 may be stored due to a malfunction in following systems. Therefore, it is necessary to check for and troubleshoot DTCs for these systems first.

·

Hybrid control system

·

Motor generator control system

·

SFI system



a.

Check for DTCs.

i.

Hybrid control system

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

ii.

Motor generator control system

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Motor Generator > Trouble Codes
50001 395

iii.

SFI system (w/ Canister pump module)

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

iv.

SFI system (w/o Canister pump module)

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372


Result:
Result Proceed to
No DTCs related to the systems listed above are output. A
Any of the DTCs related to the systems listed above is output. B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 1.3 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A63 is not output A
DTC C1A63 is output B



A

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY