Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the driving support ECU assembly when the power switch is on (IG).

WIRING DIAGRAM

E256368E52
0.385,0.896 1.813,1.146 1.427,0.25 10 false from IG1-NO. 1 Relay 2.667,1.063 3.76,1.292 1.094,0.229 10 false ECU-IG1 NO. 4 5.281,0.906 5.74,1.104 0.458,0.198 10 false B 5.281,1.938 5.74,2.135 0.458,0.198 10 false GND 5.052,1.833 5.292,2.021 0.24,0.188 10 false 28 5.115,0.802 5.229,1.01 0.115,0.208 10 false 7 4.781,2.667 6.906,2.906 2.125,0.24 10 false Driving Support ECU Assembly 4.781,2.49 5.24,2.688 0.458,0.198 10 false F40

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
A380143C02
1.594,0.198 1.979,0.427 0.385,0.229 1.26,0.958 0.896,0.354 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.219 2.125,0.417 0.458,0.198 10 false F40 0.781,0.25 0.938,0.448 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F40 driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F40-7 (B) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
A380143C03
1.594,0.198 1.979,0.427 0.385,0.229 2.281,1.813 2.479,1.281 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.219 2.125,0.417 0.458,0.198 10 false F40 1.958,1.74 2.344,1.948 0.385,0.208 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F40 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F40-28 (GND) - Body ground Always Below 1 Ω



c.

Connect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR