Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.11–2016.08
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E340107E03
0.427,0.781 2.573,0.979 2.146,0.198 10 false from Auxiliary Battery 0.76,1.573 2.906,1.771 2.146,0.198 10 false from ACC Relay 0.438,2.365 2.583,2.563 2.146,0.198 10 false from IG1 NO. 1 Relay 3.313,1.781 4.042,2.01 0.729,0.229 10 false ECU-ACC 3.406,0.969 4.135,1.26 0.729,0.292 10 false RADIO 3.188,2.563 4.719,2.813 1.531,0.25 10 false ECU-IG1 NO. 4 5.604,3.667 6.813,4.135 1.208,0.469 10 false Radio and Display Receiver Assembly 5.823,1.583 6.281,1.833 0.458,0.25 10 false ACC1 5.813,0.781 6.271,1.031 0.458,0.25 10 false +B1 5.813,2.365 6.271,2.615 0.458,0.25 10 false IG 5.802,3.167 6.26,3.417 0.458,0.25 10 false GND1 5.427,0.802 5.885,1.052 0.458,0.25 10 false F32 5.438,1.583 5.896,1.833 0.458,0.25 10 false F32 5.438,2.375 5.896,2.625 0.458,0.25 10 false F31 5.427,3.177 5.885,3.427 0.458,0.25 10 false F32 5.49,0.604 5.948,0.854 0.458,0.25 10 false 3 5.51,1.385 5.969,1.635 0.458,0.25 10 false 4 5.5,2.167 5.958,2.417 0.458,0.25 10 false 1 5.49,2.969 5.948,3.219 0.458,0.25 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the F32 and F31 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F32-4 (+B1) - F32-7 (GND1) Power switch off 11 to 14 V
F32-3 (ACC1) - F32-7 (GND1) Power switch on (ACC) 11 to 14 V
F31-1 (IG) - F32-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR