Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › MASS AIR FLOW METER
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0241782 MASS AIR FLOW METER G

2ZR-FXE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

a.

Check the output voltage.

i.
A357485C01
2.74,1.698 2.833,1.25 2.833,1.25 2.917,1.25 true 2.25,2.333 2.25,2.167 2.25,2.167 2.573,1.75 true 1.75,1.417 1.917,1.417 1.917,1.417 2.438,1.729 true 2.958,1.156 3.406,1.385 0.448,0.229 10 false 1 (+B) 2.031,2.375 2.604,2.635 0.573,0.26 10 false 2 (E2G) 1.313,1.302 1.76,1.531 0.448,0.229 10 false 3 (VG) 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a
*a Component without harness connected
(Mass Air Flow Meter Sub-assembly)
V100135

Air


Connect a battery positive (+) lead to terminal 1 (+B) and negative (-) lead to terminal 2 (E2G).

NOTICE:

While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



ii.

Connect the positive (+) tester probe to terminal 3 (VG) and negative (-) tester probe to terminal 2 (E2G).


iii.

Blow air into the mass air flow meter sub-assembly and check that the voltage fluctuates.

If the result is not as specified, replace the mass air flow meter sub-assembly.



b.
A354279C01
1.729,2.26 2.188,2.26 true 2.469,2.229 2.813,2.229 true 1.563,2.156 1.875,2.313 0.313,0.156 10 false *a 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b
*a Platinum Hot Wire (Heater)
*b Temperature Sensor (Thermistor)


Perform a visual check for any foreign matter on the platinum hot wire (heater) and temperature sensor (thermistor) of the mass air flow meter sub-assembly shown in the illustration.

OK:

There is no foreign matter.


If the result is not as specified, replace the mass air flow meter sub-assembly.


c.
A167890C07
0.802,0.958 1.063,0.958 1.063,0.958 1.333,1.458 true 1.594,1.469 1.823,0.958 1.823,0.958 2.146,0.958 true 1.344,1.448 1.448,1.594 0.104,0.146 10 false 5 1.5,1.448 1.604,1.594 0.104,0.146 10 false 4 1.656,1.448 1.76,1.594 0.104,0.146 10 false 3 1.958,1.448 2.063,1.594 0.104,0.146 10 false 1 1.802,1.448 1.906,1.594 0.104,0.146 10 false 2 2.188,0.875 2.604,1.073 0.417,0.198 10 false THA 0.594,0.875 0.854,1.052 0.26,0.177 10 false E2 0.063,0.052 0.24,0.219 0.177,0.167 10 false *a
*a Component without harness connected
(Mass Air Flow Meter Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 12.5 to 16.9 kΩ
20°C (68°F) 2.19 to 2.67 kΩ
60°C (140°F) 0.50 to 0.68 kΩ


If the result is not as specified, replace the mass air flow meter sub-assembly.