Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM3210E _59 Vehicle Exterior _047514 WIPER / WASHER _0242030 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Rain Sensor)

a.

Check the front washer operation (for Wiper Switch RH Side Type).

i.
E257039C65
0.417,0.99 0.76,1.208 0.344,0.219 2.615,1 2.969,1.219 0.354,0.219 1.969,1.375 1.625,1.719 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F65 2.677,1.031 2.99,1.229 0.313,0.198 10 false F66 1.521,1.771 1.833,1.969 0.313,0.198 10 false WF 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F66-7 (WF) and a negative (-) lead to terminal F66-4 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F66-7 (WF) and F66-4 (EW).

OK:

Voltage changes as shown in the illustration.


E226602E93
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.573,0.823 2.938,1.323 2.365,0.5 10 false Voltage between terminals F66-7 (WF) and F66-4 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false Off 3.344,0.219 3.74,0.552 0.396,0.333 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation (for Wiper Switch LH Side Type).

i.
E239385C73
0.344,1.104 0.688,1.344 0.344,0.24 2.729,1.063 3.052,1.281 0.323,0.219 0.781,1.708 0.969,1.438 false 1.417,1.438 1.615,1.719 false 0.385,1.125 0.729,1.354 0.344,0.229 10 false F66 2.76,1.094 3.115,1.323 0.354,0.229 10 false F65 0.104,0.052 0.385,0.271 0.281,0.219 10 false *a 0.625,1.76 0.906,1.958 0.281,0.198 10 false EW 1.583,1.76 1.917,1.948 0.333,0.188 10 false WF
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F66-4 (WF) and a negative (-) lead to terminal F66-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F66-4 (WF) and F66-7 (EW).

OK:

Voltage changes as shown in the illustration.


E226602E94
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.573,0.823 2.927,1.344 2.354,0.521 10 false Voltage between terminals F66-4 (WF) and F66-7 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false Off 3.344,0.219 3.74,0.552 0.396,0.333 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Auto Wiper System)

a.

Check the front wiper intermittent operation (for Wiper Switch RH Side Type).

i.
E257039C23
0.417,0.99 0.76,1.208 0.344,0.219 2.615,1 2.958,1.219 0.344,0.219 1.25,1.052 0.823,0.49 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F65 2.688,1.031 3,1.229 0.313,0.198 10 false F66 0.677,0.302 0.99,0.5 0.313,0.198 10 false +1 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F65-3 (+1) and a negative (-) lead to terminal F66-4 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Check the voltage between terminals F65-3 (+1) and F66-4 (EW) with the intermittent wiper operating at different speeds.

OK:

Voltage changes as shown in the illustration.


E136493E80
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.865,1.177 1.792,0.677 10 false Voltage between terminals F65-3 (+1) and F66-4 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 0.6 to 2.6 seconds 5.792,1 7.021,1.198 1.229,0.198 10 false 5.7 to 15.7 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front wiper intermittent operation (for Wiper Switch LH Side Type).

i.
E239385C74
0.344,1.104 0.688,1.344 0.344,0.24 2.729,1.063 3.052,1.281 0.323,0.219 0.781,1.708 0.969,1.438 false 2.219,1.083 2.625,0.51 false 0.385,1.125 0.729,1.354 0.344,0.229 10 false F66 2.76,1.094 3.115,1.323 0.354,0.229 10 false F65 0.104,0.052 0.385,0.271 0.281,0.219 10 false *a 0.625,1.76 0.906,1.958 0.281,0.198 10 false EW 2.656,0.344 2.99,0.531 0.333,0.188 10 false +1
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F65-2 (+1) and a negative (-) lead to terminal F66-7 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Check the voltage between terminals F65-2 (+1) and F66-7 (EW) with the intermittent wiper operating at different speeds.

OK:

Voltage changes as shown in the illustration.


E136493E81
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.49 1.781,0.844 1.708,0.354 10 false Voltage between terminals F65-2 (+1) and F66-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 0.6 to 2.6 seconds 5.792,1 7.031,1.198 1.24,0.198 10 false 5.7 to 15.7 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the front washer operation (for Wiper Switch RH Side Type).

i.
E257039C65
0.417,0.99 0.76,1.208 0.344,0.219 2.615,1 2.969,1.219 0.354,0.219 1.969,1.375 1.625,1.719 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F65 2.677,1.031 2.99,1.229 0.313,0.198 10 false F66 1.521,1.771 1.833,1.969 0.313,0.198 10 false WF 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F66-7 (WF) and a negative (-) lead to terminal F66-4 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F66-7 (WF) and F66-4 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E95
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.99,0.885 2.771,1.219 1.781,0.333 10 false Voltage between terminals F66-7 (WF) and F66-4 (EW): 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Check the front washer operation (for Wiper Switch LH Side Type).

i.
E239385C75
0.271,1.052 0.667,1.313 0.396,0.26 2.833,1.042 3.219,1.302 0.385,0.26 1.417,1.427 1.563,1.688 false 0.979,1.427 0.771,1.708 false 0.354,1.104 0.635,1.281 0.281,0.177 10 false F66 2.927,1.094 3.219,1.271 0.292,0.177 10 false F65 0.104,0.063 0.458,0.271 0.354,0.208 10 false *a 0.667,1.74 1,1.917 0.333,0.177 10 false EW 1.49,1.74 1.781,1.917 0.292,0.177 10 false WF
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F66-4 (WF) and a negative (-) lead to terminal F66-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F66-4 (WF) and F66-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E96
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.885 2.719,1.24 1.74,0.354 10 false Voltage between terminals F66-4 (WF) and F66-7 (EW): 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.