Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0242212 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2278  Engine/Power Switch Malfunction  


DESCRIPTION

This DTC is stored when the SSW1 contact signal and SSW2 contact signal, which are detected when the power switch is operated, do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2278 Engine/Power Switch Malfunction When the power switch is operated, the SSW1 contact signal and SSW2 contact signal do not match (1-trip detection logic*).
·

AM2 fuse

·

Power switch

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG).



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
If either the SSW1 contact signal or SSW2 contact signal is stuck on, the power source mode cannot be changed by pressing the power switch. If either the SSW1 contact signal or SSW2 contact signal is stuck off, emergency stop by pressing and holding the power switch for 2 seconds or more cannot be operated. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2278
Power Source Control
·

Starter Switch1

·

Starter Switch2



WIRING DIAGRAM

B424429E08
0.448,0.573 1.354,1.01 0.906,0.438 10 false from Auxiliary Battery 2.094,0.719 2.708,0.917 0.615,0.198 10 false AM2 2.792,0.458 3.406,0.656 0.615,0.198 10 false 4 3.552,0.323 4.167,0.521 0.615,0.198 10 false +B 2.99,2.021 3.604,2.219 0.615,0.198 10 false E 2.74,1.906 3.354,2.104 0.615,0.198 10 false 18 3.729,0.76 4.344,0.958 0.615,0.198 10 false SSW1 3.729,1.417 4.344,1.615 0.615,0.198 10 false SSW2 3.729,2.042 4.344,2.24 0.615,0.198 10 false AGND 4.219,0.771 4.833,0.969 0.615,0.198 10 false 23 4.229,1.417 4.844,1.615 0.615,0.198 10 false 21 4.219,2.042 4.833,2.24 0.615,0.198 10 false 11 5.188,0.802 5.802,1 0.615,0.198 10 false 5 5.177,1.427 5.792,1.625 0.615,0.198 10 false 1 5.177,2.052 5.792,2.25 0.615,0.198 10 false 6 5.354,0.802 5.969,1 0.615,0.198 10 false SS1 5.354,1.427 5.969,1.625 0.615,0.198 10 false SS2 5.344,2.052 5.958,2.25 0.615,0.198 10 false AGND 5.448,2.583 6.063,2.781 0.615,0.198 10 false F50 5.448,2.729 6.885,3.031 1.438,0.302 10 false Power Switch 2.896,2.729 3.51,2.927 0.615,0.198 10 false F1 2.875,2.896 4.677,3.396 1.802,0.5 10 false Certification ECU (Smart Key ECU Assembly) 2.969,0.583 3.583,0.781 0.615,0.198 10 false +B 3.156,1.188 3.771,1.385 0.615,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List while wiggling the wire harness.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the F50 power switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-23 (SSW1) - F50-5 (SS1) Always Below 1 Ω
F1-21 (SSW2) - F50-1 (SS2) Always Below 1 Ω
F1-11 (AGND) - F50-6 (AGND) Always Below 1 Ω
F1-23 (SSW1) or F50-5 (SS1) - Body ground Always 10 kΩ or higher
F1-21 (SSW2) or F50-1 (SS2) - Body ground Always 10 kΩ or higher
F1-11 (AGND) or F50-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER SWITCH
a.


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG