Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3210E _58 Vehicle Interior _047513 DOOR LOCK _0242296 POWER DOOR LOCK CONTROL SYSTEM Y

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power door lock control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS CHECK
2.CUSTOMER PROBLEM ANALYSIS CHECK
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:


What Vehicle model, system name
When Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the power switch was on, whether the hybrid control system was starting
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTCs are not output A
LIN DTCs are output B



A

6.CHECK FOR DTC (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)*

B

6.CHECK FOR DTC (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)*
a.

Clear the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Master Switch > Clear DTCs
50002 148

b.

Recheck for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148

Result:
Result Proceed to
DTC B2312 is not output A
DTC B2312 is output B



A

7.PROBLEM SYMPTOMS TABLE

B

GO TO POWER WINDOW CONTROL SYSTEM

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END