Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3210E _55 Steering _047547 POWER ASSIST SYSTEMS _0242387 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly distinguishes the power switch status as on (IG) or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1551 IG Power Supply Voltage Open or short in IG power source circuit with power switch on (IG)
·

EPS-IG1 fuse

·

IG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the power switch is turned on (IG) again -

WIRING DIAGRAM

C320443E06
5.646,2.823 6.646,3.271 1,0.448 10 false Power Steering ECU Assembly 3.708,0.875 4.438,1.104 0.729,0.229 10 false EPS-IG1 5.292,0.719 5.729,1.021 0.438,0.302 10 false F20 5.292,1.906 5.646,2.125 0.354,0.219 10 false F54 5.385,0.521 5.823,0.823 0.438,0.302 10 false 1 5.667,0.708 6.104,1.01 0.438,0.302 10 false IG 5.677,1.917 6.115,2.219 0.438,0.302 10 false PGND 5.385,1.708 5.823,2.01 0.438,0.302 10 false 2 1.427,0.688 2.99,1.073 1.563,0.385 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the F54 and F20 power steering ECU assembly connectors.

C319557C17
2.094,0.344 2.542,0.583 0.448,0.24 5.083,0.344 5.531,0.583 0.448,0.24 4.646,1.938 5.031,1.375 false 2.667,2.167 2.667,1.625 false 0.323,0.135 0.635,0.292 0.313,0.156 10 false *a 2.198,0.375 2.729,0.667 0.531,0.292 10 false F54 5.188,0.375 5.719,0.667 0.531,0.292 10 false F20 2.49,2.219 3.021,2.51 0.531,0.292 10 false PGND 4.583,1.979 5.115,2.271 0.531,0.292 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F20-1 (IG) - Body ground Power switch on (IG) 8 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR