Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3210E _55 Steering _047547 POWER ASSIST SYSTEMS _0242387 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the power steering ECU assembly stores a DTC and illuminates the EPS warning light.

WIRING DIAGRAM

C322366E09
1.74,0.49 2.354,0.688 0.615,0.198 10 false CANH 1.75,0.875 2.365,1.073 0.615,0.198 10 false CANL 2.229,0.365 2.844,0.563 0.615,0.198 10 false 26 2.229,0.76 2.844,0.958 0.615,0.198 10 false 27 0.844,1.073 1.458,1.271 0.615,0.198 10 false F6 1.438,1.938 2.927,2.156 1.49,0.219 10 false from IG1-NO. 1 Relay 3.708,2.104 4.396,2.344 0.688,0.24 10 false EPS-IG1 5.292,0.51 5.906,0.708 0.615,0.198 10 false F20 5.292,0.906 5.906,1.104 0.615,0.198 10 false F20 5.385,0.729 6,0.927 0.615,0.198 10 false 8 5.385,0.323 6,0.521 0.615,0.198 10 false 7 5.698,0.51 6.313,0.708 0.615,0.198 10 false CANH 5.688,0.906 6.302,1.104 0.615,0.198 10 false CANL 5.688,1.958 6.302,2.156 0.615,0.198 10 false IG 5.698,2.563 6.313,2.76 0.615,0.198 10 false PIG 5.677,3.229 6.292,3.427 0.615,0.198 10 false PGND 3.813,2.719 5.188,2.917 1.375,0.198 10 false EPS 5.292,1.948 5.906,2.146 0.615,0.198 10 false F20 5.292,2.563 5.906,2.76 0.615,0.198 10 false F54 5.292,3.219 5.906,3.417 0.615,0.198 10 false F54 5.365,1.771 5.688,1.958 0.323,0.188 10 false 1 5.375,2.365 5.698,2.552 0.323,0.188 10 false 1 5.385,3.031 5.708,3.219 0.323,0.188 10 false 2 1.438,2.542 3.906,2.792 2.469,0.25 10 false from Auxiliary Battery 0.833,1.24 2.656,1.708 1.823,0.469 10 false Combination Meter Assembly (Meter Circuit Plate) 0.792,4.323 2.885,4.531 2.094,0.208 10 false : CAN Communication Line 5.625,3.813 6.625,4.24 1,0.427 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Jiggle the power steering ECU assembly connectors and wire harness up and down, and left and right to check the illumination condition of the EPS warning light in the combination meter assembly (meter circuit plate).

OK:

The EPS warning light illumination condition does not change.


HINT:

When the EPS warning light is operating properly, it illuminates when the power switch is turned on (IG) and turns off when the power switch is turn on (READY).



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)

B

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)
a.

Disconnect the F54 and F20 power steering ECU assembly connectors.


C319557C18
2.094,0.344 2.542,0.583 0.448,0.24 5.083,0.344 5.531,0.583 0.448,0.24 4.646,1.938 5.031,1.375 false 2.854,2.188 2.708,1.625 false 1.594,2.146 1.833,1.635 false 0.323,0.135 0.635,0.292 0.313,0.156 10 false *a 2.208,0.375 2.74,0.667 0.531,0.292 10 false F54 5.198,0.375 5.729,0.667 0.531,0.292 10 false F20 2.677,2.24 3.208,2.531 0.531,0.292 10 false PGND 4.583,1.979 5.115,2.271 0.531,0.292 10 false IG 1.479,2.24 2.01,2.531 0.531,0.292 10 false PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F20-1 (IG) - Body ground Power switch on (IG) 8 to 16 V
F54-1 (PIG) - Body ground Power switch on (IG) 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Connect the F54 and F20 power steering ECU assembly connectors.


b.

Perform the Active Test of the combination meter assembly (meter circuit plate) using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EPS
50004 122 22

c.

Check the combination meter assembly (meter circuit plate).

OK:

The EPS warning light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

NG