Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3210E _55 Steering _047547 POWER ASSIST SYSTEMS _0242387 POWER STEERING SYSTEM L

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following system(s) after the cable is reconnected.

System Procedure
Lane Departure Alert System (w/ Steering Control) (Click here)
Intelligent Clearance Sonar System
Parking Assist Monitor System
Simple Intelligent Parking Assist System
Power Door Lock Control System
Pre-crash Safety System



HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM


a.

This vehicle is equipped with a Supplemental Restraint System (SRS). Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing. This may cause a serious accident.

Before servicing (including inspection, replacement, removal and installation of parts), be sure to read the precautionary notices for the Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF ELECTRONIC POWER STEERING COMPONENTS


a.

Be sure to align the front wheels straight ahead when removing and installing the steering gear assembly.


b.

When disconnecting the steering intermediate shaft assembly, be sure to place matchmarks before starting the operation.


c.

After replacing the electric power steering column sub-assembly or power steering ECU assembly, calibrate the torque sensor zero point.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



HANDLING PRECAUTION


a.

When handling electronic parts:

i.

Do not subject any parts such as ECUs and relays to any impact. Replace them with new ones if dropped or subjected to a strong impact.


ii.

Do not expose any electronic parts to high temperatures or humidity.


iii.

In order to prevent deformation or malfunctions due to static electricity, do not touch the connector terminals.



b.

When handling the power steering ECU assembly:

i.

When the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



c.

When handling the electric power steering column sub-assembly:

i.

Do not subject the electric power steering column sub-assembly (especially the motor and torque sensor) to any impact. Replace the electric power steering column sub-assembly with a new one if subjected to a strong impact.


ii.

Do not pull the wire harness when moving the electric power steering column sub-assembly.


iii.

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



d.

When disconnecting and reconnecting the connectors:

i.

Before disconnecting connectors related to the power steering system, turn the power switch on (IG), center the steering wheel, turn the power switch off, and then disconnect the connectors.


ii.

Before reconnecting connectors related to the power steering system, ensure that the power switch is off. Then center the steering wheel and turn the power switch on (IG).

NOTICE:

Do not turn the power switch on (IG) when the steering wheel is not centered.



iii.

If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between turning right and left. If there is a difference in steering effort between turning right and left, perform torque sensor zero point calibration after initializing the torque sensor zero point.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION




PRECAUTIONS FOR CAN COMMUNICATION


a.

CAN communication lines are used to receive information from the skid control ECU (brake booster with master cylinder assembly) and hybrid vehicle control ECU and to transmit warnings to the combination meter assembly (meter circuit plate). When problems are detected in the CAN communication lines, CAN communication DTCs are stored.


b.

If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.


c.

The wiring used for each communication line is a twisted pair of wires that have an equal length. Do not temporarily repair a CAN communication line with a bypass wire or equivalent.