Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › 2015.11–2016.08
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243313 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

When installing the name plates, heat the vehicle body, back door outside garnish and name plates using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
·

Back Door Outside Garnish

·

Name Plate


20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body, back door outside garnish or name plate excessively.


PROCEDURE

Hide 75374 1.INSTALL SIDE PANEL EMBLEM

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the vehicle body and a new side panel emblem.


c.

Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for LH Side:

i.

Install the side panel emblem as shown in the illustration.

B435987N01
0.927,1.583 1.083,1.781 0.156,0.198 10 false A 2.313,1.063 2.469,1.26 0.156,0.198 10 true B

Standard Measurement:
Area Measurement Area Measurement
A 133.9 mm (5.27 in.) B 95.5 mm (3.76 in.)




e.

for RH Side:

i.

Install the side panel emblem as shown in the illustration.

B435988N01
4.448,1.052 4.604,1.25 0.156,0.198 10 true A 5.865,1.594 6.063,1.823 0.198,0.229 10 false B

Standard Measurement:
Area Measurement Area Measurement
A 95.1 mm (3.74 in.) B 136.2 mm (5.36 in.)




Hide 75403 2.INSTALL BACK DOOR ORNAMENT SUB-ASSEMBLY

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new back door ornament sub-assembly.


c.

Remove the release paper from the back door ornament sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the 2 pins and install the back door ornament sub-assembly as shown in the illustration.

B435981


Hide 75443A 3.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR PLATE

for PRIUS Plate:

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 3 luggage compartment door plate.


c.

Remove the release paper from the No. 3 luggage compartment door plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 3 luggage compartment door plate as shown in the illustration.

B436132C01
1.771,1.625 1.354,1.188 true 3.25,1.625 2.906,1.354 true 0.781,1.896 0.625,1.896 true 1.156,1.052 1.469,1.208 0.313,0.156 10 false *a 0.438,1.802 0.75,1.958 0.313,0.156 10 false *b 2.719,1.24 3.031,1.396 0.313,0.156 10 false *a 0.177,1.198 0.333,1.396 0.156,0.198 10 false A 1.24,0.531 1.427,0.719 0.188,0.188 10 false B 1.875,0.188 2.125,0.417 0.25,0.229 10 false C 3.677,1.188 3.927,1.406 0.25,0.219 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 105.6 mm (4.16 in.) B 100.9 mm (3.97 in.)
C 235.6 mm (9.28 in.) D 97.9 mm (3.85 in.)



Hide 75443A 4.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR PLATE

for TOYOTA Plate:

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 3 luggage compartment door plate.


c.

Remove the release paper from the No. 3 luggage compartment door plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 3 luggage compartment door plate as shown in the illustration.

B435984C01
1.344,1.344 1.708,1.635 true 2.458,1.333 2.823,1.625 true 0.594,1.885 0.771,1.885 true 1.156,1.24 1.469,1.396 0.313,0.156 10 false *a 0.385,1.792 0.698,1.948 0.313,0.156 10 false *b 2.271,1.208 2.583,1.365 0.313,0.156 10 false *a 0.135,1.219 0.333,1.469 0.198,0.25 10 false A 1.031,0.552 1.229,0.802 0.198,0.25 10 false B 1.656,0.219 1.854,0.469 0.198,0.25 10 false C 3.667,1.188 3.865,1.438 0.198,0.25 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 107.9 mm (4.25 in.) B 95.7 mm (3.77 in.)
C 201 mm (7.91 in.) D 102 mm (4.02 in.)



Hide 75441E 5.INSTALL NO. 1 BACK DOOR NAME PLATE

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 1 back door name plate.


c.

Remove the release paper from the No. 1 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 1 back door name plate as shown in the illustration.

B435986C01
4.76,1.302 4.917,1.448 false 6.177,1.292 5.969,1.385 false 6.667,0.948 6.521,0.948 false 4.969,1.427 5.281,1.583 0.313,0.156 10 false *a 6.729,0.865 7.021,1.073 0.292,0.208 10 false *b 5.76,1.344 6.073,1.5 0.313,0.156 10 false *a 4.427,1.438 4.656,1.656 0.229,0.219 10 false A 5.438,2.146 5.667,2.365 0.229,0.219 10 false B 6.229,1.823 6.458,2.042 0.229,0.219 10 false C 6.74,1.281 6.969,1.5 0.229,0.219 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 32.5 mm (1.28 in.) B 146.1 mm (5.75 in.)
C 18.4 mm (0.724 in.) D 18 mm (0.709 in.)



Hide 75442 6.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

for HYBRID Plate:

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 2 luggage compartment door name plate.


c.

Remove the release paper from the No. 2 luggage compartment door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 2 luggage compartment door name plate as shown in the illustration.

B435982C01
4.01,1.583 4.198,1.427 false 5.406,1.563 5.594,1.406 false 6.365,1.948 6.521,1.948 false 4.25,1.323 4.563,1.479 0.313,0.156 10 false *a 6.573,1.875 6.885,2.031 0.313,0.156 10 false *b 5.625,1.302 5.938,1.458 0.313,0.156 10 true *a 3.396,1.198 3.604,1.406 0.208,0.208 10 false A 5.083,0.24 5.292,0.448 0.208,0.208 10 false B 5.906,0.5 6.115,0.708 0.208,0.208 10 false C 6.896,1.135 7.104,1.344 0.208,0.208 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 98.5 mm (3.88 in.) B 231.9 mm (9.13 in.)
C 103.3 mm (4.07 in.) D 102.3 mm (4.03 in.)



Hide 75442 7.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

for PRIUS Plate:

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 2 luggage compartment door name plate.


c.

Remove the release paper from the No. 2 luggage compartment door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 2 luggage compartment door name plate as shown in the illustration.

B435985C01
3.938,1.573 4.094,1.458 false 5.417,1.594 5.573,1.479 false 6.365,1.917 6.5,1.917 false 4.188,1.344 4.5,1.5 0.313,0.156 10 false *a 6.521,1.823 6.833,1.979 0.313,0.156 10 false *b 5.604,1.365 5.917,1.521 0.313,0.156 10 true *a 3.385,1.24 3.573,1.448 0.188,0.208 10 false A 5.083,0.271 5.271,0.479 0.188,0.208 10 false B 5.927,0.594 6.115,0.802 0.188,0.208 10 false C 6.854,1.115 7.042,1.323 0.188,0.208 10 false D
*a Edge of Curved Surface *b Profile of Back Door Outside Garnish


Standard Measurement:
Area Measurement Area Measurement
A 95.7 mm (3.77 in.) B 238.9 mm (9.41 in.)
C 103.7 mm (4.08 in.) D 104.1 mm (4.10 in.)