Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(for LHD)
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0243381 BRAKE ACTUATOR(for LHD) G

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  INSPECTION  


PROCEDURE

Hide 44510 1.INSPECT BRAKE ACTUATOR ASSEMBLY

a.

Inspect the solenoid circuit.

i.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.


C306841C24
4.542,1.063 4.927,0.531 true 3.958,1.052 4.177,0.51 true 3.333,1.052 3.229,0.51 true 2.729,1.052 2.552,0.563 true 1.365,2.135 2.052,1.698 true 2.083,2.25 2.396,1.677 true 2.885,2.323 3.021,1.698 true 4.083,2.323 3.677,1.677 true 4.854,2.26 4.229,1.688 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 4.802,0.354 5.271,0.563 0.469,0.208 10 false SFRR 4.042,0.333 4.448,0.552 0.406,0.219 10 false SRRR 3.094,0.333 3.49,0.531 0.396,0.198 10 false SFRH 2.385,0.365 2.792,0.542 0.406,0.177 10 false SRRH 1.104,2.135 1.417,2.333 0.313,0.198 10 false +BS 1.906,2.281 2.323,2.49 0.417,0.208 10 false SFLH 2.719,2.354 3.167,2.573 0.448,0.219 10 false SRLH 3.948,2.354 4.344,2.552 0.396,0.198 10 false SFLR 4.76,2.292 5.188,2.51 0.427,0.219 10 false SRLR
*a Component without harness connected
(Brake Actuator Assembly)
- -



ii.

Disconnect the brake actuator assembly connector.


iii.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



iv.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the brake actuator assembly when it is cooled down.


Standard Resistance:
Tester Connection Condition Specified Condition
38 (+BS) - 8 (SFRH) Always 6.4 to 7.0 Ω
38 (+BS) - 37 (SFLH) Always 6.4 to 7.0 Ω
38 (+BS) - 11 (SRRH) Always 6.4 to 7.0 Ω
38 (+BS) - 34 (SRLH) Always 6.4 to 7.0 Ω
38 (+BS) - 2 (SFRR) Always 5.1 to 5.7 Ω
38 (+BS) - 31 (SFLR) Always 5.1 to 5.7 Ω
38 (+BS) - 5 (SRRR) Always 5.1 to 5.7 Ω
38 (+BS) - 28 (SRLR) Always 5.1 to 5.7 Ω


If the result is not as specified, replace the brake actuator assembly.