Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD)
RM3210E _54 Brake _047517 BRAKE SYSTEM (OTHER) _0243391 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 44551C 2.SEPARATE NO. 1 BRAKE ACTUATOR TUBE

a.
C346773

Remove the 2 nuts and separate the No. 1 brake actuator tube.


Hide 473A1 3.REMOVE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C347153

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster with master cylinder assembly.


b.

Disengage the claw to separate the clamp cover.

C347155C01
2.875,0.188 3.063,0.188 3.063,0.188 3.063,0.469 true 2.719,0.104 2.906,0.292 0.188,0.188 10 false *a
*a Clamp Cover - -



c.

Disengage the 3 clamps and remove the accumulator to brake master cylinder tube.


Hide 47070 4.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C347157

Disengage the clamp to separate the No. 3 front brake tube from the brake actuator bracket assembly.


b.
C347159

Remove the 2 nuts.


c.

Remove the bolt of the brake actuator bracket assembly.

C347160C01
2.188,3.344 2.448,3.344 2.448,3.344 2.625,3.167 false 4.375,3.458 4.583,3.24 4.583,3.24 4.865,3.24 false 2.958,3.594 3.542,3.594 false 3.667,3.396 4.031,2.823 4.031,2.823 4.313,2.823 false 2.031,3.26 2.344,3.417 0.313,0.156 10 false *a 4.896,3.156 5.208,3.313 0.313,0.156 10 false *b 2.792,3.51 3.104,3.667 0.313,0.156 10 false *c 4.344,2.74 4.656,2.896 0.313,0.156 10 false *d
*a Union *b Connector
*c Wire Harness *d Stud
V113147

Remove in this Direction - -



d.

Remove the brake booster pump assembly as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.



HINT:

Move the brake actuator bracket assembly as necessary to allow the brake booster pump assembly to be removed.



e.

Remove the brake actuator bracket assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



f.
C347165

Remove the brake actuator case collar and brake booster pump bushing from the brake actuator bracket assembly.


Hide 44571A 5.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C347162

Slide the clip and remove the No. 1 brake actuator hose from the brake booster pump assembly.


Hide 47381 6.REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

a.
C347164

Remove the bolt and No. 1 brake tube clamp bracket from the brake booster pump assembly.