Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E344933E01
2.458,3.292 5.094,3.552 2.635,0.26 10 false : Data Signal (USB Communication Line) 5.667,2.771 6.854,3.208 1.188,0.438 10 false Radio and Display Receiver Assembly 0.323,2.823 1.5,3.313 1.177,0.49 10 false No. 1 Stereo Jack Adapter Assembly 0.271,2.656 0.75,2.906 0.479,0.25 10 false F39 5.656,2.604 6.104,2.906 0.448,0.302 10 false F91 3.271,1.75 3.99,2.021 0.719,0.271 10 false (Shielded) 0.906,2.24 1.385,2.49 0.479,0.25 10 false UJSS 0.865,1.458 1.344,1.708 0.479,0.25 10 false UDO+ 0.865,0.656 1.344,0.906 0.479,0.25 10 false UDO- 1.323,0.542 1.708,0.802 0.385,0.26 10 false 2 1.344,1.313 1.729,1.573 0.385,0.26 10 false 3 1.333,2.115 1.719,2.375 0.385,0.26 10 false 5 5.74,0.521 6.125,0.781 0.385,0.26 10 false 2 5.729,1.292 6.115,1.552 0.385,0.26 10 false 3 5.729,2.094 6.115,2.354 0.385,0.26 10 false 5 5.917,2.25 6.396,2.5 0.479,0.25 10 false USG1 5.927,1.49 6.406,1.74 0.479,0.25 10 false US1+ 5.917,0.677 6.396,0.927 0.479,0.25 10 false US1-

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the F91 radio and display receiver assembly connector.


b.

Disconnect the F39 No. 1 stereo jack adapter assembly connector.


c.
E249132C10
1.5,0.198 1.906,0.438 0.406,0.24 1.5,2.292 1.906,2.531 0.406,0.24 1.094,1.552 1.573,1.417 false 1.833,1.417 2.313,1.51 false 1.854,1.552 2.302,1.875 false 1.083,3.854 1.615,3.438 false 1.813,3.448 2.438,3.719 false 1.802,3.521 2.448,4.01 false 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b 1.583,0.219 1.896,0.417 0.313,0.198 10 false F91 1.583,2.313 1.896,2.51 0.313,0.198 10 false F39 0.708,1.49 1.302,1.688 0.594,0.198 10 false US1+ 2.365,1.438 2.792,1.667 0.427,0.229 10 false US1- 2.365,1.833 2.875,2.156 0.51,0.323 10 false USG1 0.75,3.833 1.229,4.125 0.479,0.292 10 false UDO- 2.49,3.656 3,3.885 0.51,0.229 10 false UDO+ 2.49,3.958 2.906,4.167 0.417,0.208 10 false UJSS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F91-2 (US1-) - F39-2 (UDO-) Always Below 1 Ω
F91-3 (US1+) - F39-3 (UDO+) Always Below 1 Ω
F91-5 (USG1) - F39-5 (UJSS) Always Below 1 Ω
F91-2 (US1-) or F39-2 (UDO-) - Body ground Always 10 kΩ or higher
F91-3 (US1+) or F39-3 (UDO+) - Body ground Always 10 kΩ or higher
F91-5 (USG1) or F39-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR