Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E334511E02
1.208,0.542 2.698,0.823 1.49,0.281 10 false from Auxiliary Battery 1.531,1.104 3.021,1.385 1.49,0.281 10 false from ACC Relay 1.219,1.677 2.708,1.958 1.49,0.281 10 false from IG1-NO. 1 Relay 3.729,0.719 4.281,1.021 0.552,0.302 10 false RADIO 3.646,1.271 5.135,1.552 1.49,0.281 10 false ECU-ACC 3.521,1.844 5.01,2.125 1.49,0.281 10 false ECU-IG1 NO. 4 5.406,2.75 6.583,3.344 1.177,0.594 10 false Radio and Display Receiver Assembly 5.281,2.042 5.604,2.26 0.323,0.219 10 false 7 5.271,1.49 5.594,1.708 0.323,0.219 10 false 1 5.271,0.927 5.594,1.146 0.323,0.219 10 false 3 5.198,0.563 5.521,0.781 0.323,0.219 10 false F32 5.281,0.365 5.604,0.583 0.323,0.219 10 false 4 5.583,0.563 6.135,0.875 0.552,0.313 10 false +B1 5.594,1.115 6.146,1.427 0.552,0.313 10 false ACC1 5.594,1.677 6.146,1.99 0.552,0.313 10 false IG 5.583,2.24 6.135,2.552 0.552,0.313 10 false GND1 5.198,1.125 5.521,1.344 0.323,0.219 10 false F32 5.188,1.688 5.51,1.906 0.323,0.219 10 false F31 5.219,2.25 5.542,2.469 0.323,0.219 10 false F32

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the F32 and F31 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F32-4 (+B1) - F32-7 (GND1) Power switch off 11 to 14 V
F32-3 (ACC1) - F32-7 (GND1) Power switch on (ACC) 11 to 14 V
F31-1 (IG) - F32-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR