Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headup Display Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headup Display Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Head Up Display" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Head Up Display" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Head Up Display" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Headup Display Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Combination meter mirror ECU branch line or connector

·

Power source circuit of combination meter mirror ECU

·

Combination meter mirror ECU ground circuit

·

Combination meter mirror ECU



WIRING DIAGRAM

C348667E18
0.625,1.958 3.427,2.271 2.802,0.313 10 false No. 3 CAN Junction Connector 0.302,1.958 0.635,2.219 0.333,0.26 10 false F71 1.719,1.448 2.052,1.708 0.333,0.26 10 false 18 1.76,0.865 2.094,1.125 0.333,0.26 10 false 7 5.396,0.865 5.729,1.125 0.333,0.26 10 false 4 5.385,1.438 5.719,1.698 0.333,0.26 10 false 5 3.833,2.281 4.927,2.594 1.094,0.313 10 false ECU-DCC NO. 2 5.385,2.344 5.719,2.604 0.333,0.26 10 false 1 5.385,3.177 5.719,3.438 0.333,0.26 10 false 2 3.833,3.104 4.875,3.406 1.042,0.302 10 false ECU-IG1 NO. 4 1.708,2.448 3.396,2.771 1.688,0.323 10 false from Auxiliary Battery 1.708,3.281 3.271,3.594 1.563,0.313 10 false from IG1-NO. 1 Relay 5.396,3.99 5.729,4.25 0.333,0.26 10 false 6 5.656,4.146 5.99,4.406 0.333,0.26 10 false ES 5.667,3.313 6,3.573 0.333,0.26 10 false IG 5.667,2.5 6,2.76 0.333,0.26 10 false B 5.656,0.99 6.281,1.24 0.625,0.25 10 false CANH 5.667,1.573 6.344,1.885 0.677,0.313 10 false CANL 5.323,4.781 5.656,5.042 0.333,0.26 10 false G7 5.573,4.781 6.76,5.344 1.188,0.563 10 false Combination Meter Mirror ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 13 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER MIRROR ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.
C346988C06
1.49,0.115 1.885,0.354 0.396,0.24 1.417,0.5 1.635,0.5 1.635,0.5 1.635,1.156 true 2.031,0.5 1.781,0.5 1.781,0.5 1.781,1.156 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.615,0.177 1.927,0.333 0.313,0.156 10 false G7 0.979,0.427 1.406,0.604 0.427,0.177 10 false CANH 2.104,0.417 2.531,0.594 0.427,0.177 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Mirror ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-4 (CANH) - G7-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (COMBINATION METER MIRROR ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346988C10
1.49,0.115 1.885,0.354 0.396,0.24 0.99,0.5 1.208,0.5 1.208,0.5 1.208,1.156 true 1.594,0.5 1.344,0.5 1.344,0.5 1.344,1.156 true 2.167,0.51 1.917,0.51 1.917,0.51 1.917,1.167 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.604,0.156 1.917,0.313 0.313,0.156 10 false G7 0.833,0.427 1.26,0.604 0.427,0.177 10 false B 1.667,0.427 2.094,0.604 0.427,0.177 10 false IG 2.25,0.438 2.677,0.615 0.427,0.177 10 false ES
*a Front view of wire harness connector
(to Combination Meter Mirror ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (ES) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (B) - Body ground Power switch off 11 to 14 V
G7-2 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)