Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM3210E _59 Vehicle Exterior _047530 SLIDING ROOF / CONVERTIBLE _0244347 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  REASSEMBLY  


PROCEDURE

Hide 63205A 1.INSTALL SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

a.
B432093C01
0,0 0,0 false
V113146

Hold Position


Hold down the roof wind deflector panel sub-assembly.


b.
B432102C01
1.146,3.406 0.969,3.792 true 0.896,3.802 1.208,3.958 0.313,0.156 10 false *a
*a Protective Tape
V113146

Push Position
V113147

Install in this Direction


Using a screwdriver, slide the sliding roof drive cable LH as shown in the illustration to install it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side.




c.
B432103C01
1.5,0.76 1.052,1.104 1.052,1.104 1.479,1 true 1.948,0.771 2.417,1.104 2.417,1.104 1.958,1.01 true 0.865,1.031 1.052,1.188 0.188,0.156 10 true *a 2.438,1.052 2.625,1.208 0.188,0.156 10 true *a
*a Alignment Mark


Adjust Fully Closed Position:

i.

Using a screwdriver, slide the sliding roof drive cable LH in either direction and align the alignment marks as shown in the illustration.

HINT:

Use the same procedure for the RH side.




d.
B432089C01
0,0 0,0 false
V113147

Install in this Direction


Insert the rear roof drip channel into the sliding roof housing sub-assembly as shown in the illustration.


e.

Engage the 2 claws as shown in the illustration to install the rear roof drip channel.

B436143C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 63306 2.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B432082C01
0,0 0,0 false
V113147

Install in this Direction


Insert the sunshade trim sub-assembly into the sliding roof housing sub-assembly as shown in the illustration.


b.
B432086C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear sliding roof sunshade stopper as shown in the illustration.

HINT:

Use the same procedure for the RH side.



c.
B432081C01
1.229,0.792 1.385,0.99 0.156,0.198 10 false B 2.281,0.365 2.417,0.531 0.135,0.167 10 true A 2.656,0.729 2.792,0.896 0.135,0.167 10 true A
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides (A).


d.

Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (2) shown in the illustration to engage the guide (B).


e.

Install the sliding roof piece sub-assembly LH with the screw.

HINT:

Use the same procedure for the RH side.



Hide 63260A 3.INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.

Apply MP grease to the gear of the sliding roof drive gear sub-assembly.


b.
B432079

Install the sliding roof drive gear sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
B432078C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


d.

Install the map light bracket with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)