Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244351 FRONT CAMERA N

CRUISE CONTROL  FRONT CAMERA  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


HINT:

When performing forward recognition camera optical axis learning, use Sequential Recognition.

E344063C01
0.833,0.167 1.333,0.5 0.5,0.333 12 false *A 4.021,0.167 4.5,0.5 0.479,0.333 12 false *B
*A One Time Recognition *B Sequential Recognition


Recognition Method Target Position Number of Times Target Recognition Performed
One Time Recognition 1 (In front of front bumper) 1
Sequential Recognition 3 (3 m (9.84 ft.) from the forward recognition camera) 3

·

One Time Recognition is an optical learning method in which 3 targets are recognized simultaneously at 1 position directly in front of the front bumper.

·

Sequential Recognition is an optical learning method in which 1 target is recognized sequentially at 3 positions 3 m (9.84 ft.) from the forward recognition camera.



PROCEDURE

Hide 1. PREPARATION FOR FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

a.
E336334C01
0.115,1.156 0.427,1.313 0.313,0.156 10 false *a 0.969,0.333 1.281,0.49 0.313,0.156 10 false *a
*a 3 m (9.84 ft.)


Park the vehicle on a level surface.

NOTICE:
·

Make sure there are no black and white patterned objects in front of the vehicle.

·

Make sure that the area shown in the illustration in front of the vehicle is free of reflective or shiny objects.

·

Perform the following procedures indoors.

·

Perform the following procedures in an area with no wind.

·

Perform the following procedures in a bright area.




b.

Check the levelness of the ground.

i.
E336335C01
0.948,0.76 1.26,0.917 0.313,0.156 10 false *a
*a 2.2 m (7.22 ft.)
V100155

Levelness Check Point


Check the levelness of the ground at the 3 points shown in the illustration.


ii.

Place the level on each levelness check point and check that the air bubble of the level is centered.

E344401



c.

Adjust the tire inflation pressure to the specified pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


d.

Clean the windshield glass.


Hide 2. PERFORM FORWARD RECOGNITION CAMERA LEARNING

a.

Create a target sheet.

i.

Print the illustration.

E144732


ii.
E102781C05
0.292,2.104 0.729,2.271 0.438,0.167 10 false *a 2.781,1.042 3.063,1.313 0.281,0.271 10 false *c 0.969,2.354 1.396,2.542 0.427,0.188 10 false *b 1.333,2.802 1.865,3.021 0.531,0.219 10 false *c
*a 18 mm (0.709 in.)
*b 90 mm (3.54 in.)
*c 180 mm (7.09 in.)


Check that the dimensions are within the values shown in the illustration.

NOTICE:
·

Make sure that the black areas of the target sheet are not glossy.

·

Make sure that the borders of the black and white areas on the target sheet are straight, and are not warped or blurry.



HINT:

If the dimensions of the created target sheet are not within +/- 5 mm (0.197 in.) of the specified values, adjust the printer settings and reprint the target sheet so that the dimensions are as specified.




b.
E190544C02
1.063,0.99 0.625,1.302 false 2.292,0.927 2.698,0.688 false 2.75,0.594 3.063,0.75 0.313,0.156 10 false *a 0.458,1.229 0.771,1.385 0.313,0.156 10 false *b
*a Target Sheet
*b Cardboard


Attach the target sheet.

i.

Cut a piece of cardboard to the same size as the target sheet.


ii.

Place the target sheet on the cardboard with the black area at the top right as shown in the illustration, and securely attach the target sheet using double-sided tape.

NOTICE:

Do not attach reflective materials, such as clear adhesive tape, to the target sheet surface as this may affect target recognition.



iii.
E320104C03
2.51,1.583 2.833,1.479 false 2.583,2.313 2.906,2.208 true 2.458,2.906 2.719,2.833 false 0.438,1.677 0.656,1.625 false 2.865,1.385 3.177,1.542 0.313,0.156 10 false *a 2.938,2.135 3.25,2.292 0.313,0.156 10 false *b 2.75,2.75 3.063,2.906 0.313,0.156 10 false *c 0.156,1.604 0.615,1.802 0.458,0.198 10 false SST 2.198,0.51 2.354,0.708 0.156,0.198 10 false A 2.198,0.771 2.354,0.969 0.156,0.198 10 false B 2.333,1.104 2.49,1.302 0.156,0.198 10 false C
*a String
*b Weight
*c Mark-off Line


Hang a weight with a pointed tip from the top center of the target sheet as shown in the illustration.

SST
09870-60000  (09870-60010, 09870-60020)


iv.

Using double-sided tape, attach the target sheet to the reflector so that the weight is aligned with the mark-off line of SST.

HINT:

Make sure that the points (A), (B) and (C) of the target sheet are aligned with the string.



v.
E320105C01
1.344,1.813 0.938,1.958 false 2.208,2.042 2.521,2.198 0.313,0.156 10 false *a 0.646,1.896 1.042,2.094 0.396,0.198 10 false SST
*a 1350 mm (53.15 in.)


Move the reflector up or down so that the center of the target sheet is at the height shown in the illustration, and secure the reflector in place.

HINT:

If the center of the target sheet is not within +/- 6 mm (0.236 in.) of the height specified, adjust the position of the reflector so that the height is as specified.




c.

Determine the target placement position.

NOTICE:
·

Make sure the background behind the target has no patterns.

·

Make sure that there are no reflective or shiny objects around the target.

·

Make sure that the shadow of the target is not cast onto a wall as this may cause a target recognition error.



i.

Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.

E336342C01
2.667,2.5 3,2.417 false 3.031,2.479 3.365,2.563 false 4.917,0.417 5.5,0.75 true 4.833,1.417 5.5,1.167 true 4.75,0.344 5.063,0.5 0.313,0.156 10 false *a 2.521,2.438 2.833,2.594 0.313,0.156 10 false *b 4.677,1.344 4.99,1.5 0.313,0.156 10 false *c 3.396,2.51 3.552,2.708 0.156,0.198 10 false A
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



ii.

Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.

E336343C01
1.188,0.5 1.521,0.583 false 3.396,2.583 3.729,2.5 false 3.771,2.417 4.104,2.5 false 0.688,1 1.521,1.167 true 1.031,0.427 1.344,0.583 0.313,0.156 10 false *a 4.125,2.438 4.438,2.594 0.313,0.156 10 false *b 0.521,0.917 0.833,1.073 0.313,0.156 10 false *c 3.292,2.521 3.5,2.75 0.208,0.229 10 false B
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Using tape and a string, create a line that connects point B to point A and extends at least 2200 mm (7.22 ft.) beyond the front center point of the vehicle.

E336336C01
2.042,3.125 2.042,2.875 false 1.896,3.125 1.896,2.875 false 2.292,2 2.042,2 false 2.313,1.823 2.063,1.823 false 0.927,2.458 0.844,2.792 false 6.74,2.458 6.823,2.792 false 0.583,2.271 0.896,2.427 0.313,0.156 10 false *a 0.781,2.792 1.094,2.948 0.313,0.156 10 false *b 2.719,1.406 3.031,1.563 0.313,0.156 10 false *c 2.094,0.5 2.406,0.656 0.313,0.156 10 false *d 6.771,2.802 7.083,2.958 0.313,0.156 10 false *b 6.5,2.156 6.656,2.354 0.156,0.198 10 false A 2.885,2.156 3.042,2.354 0.156,0.198 10 false B 2.438,2.156 2.594,2.354 0.156,0.198 10 false C 1.24,2.156 1.396,2.354 0.156,0.198 10 false D 1.813,1.854 1.969,2.052 0.156,0.198 10 false J 1.792,2.74 1.948,2.938 0.156,0.198 10 false G 2.021,3.135 2.177,3.333 0.156,0.198 10 false E 1.875,3.135 2.031,3.333 0.156,0.198 10 false F 2.354,1.76 2.51,1.958 0.156,0.198 10 false H 2.344,1.938 2.5,2.135 0.156,0.198 10 false I
*a String *b Tape
*c 481 mm (1.58 ft.) *d 2151 mm (7.06 ft.)


HINT:
·

Make sure the string is taut when securing it with tape.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




iv.

Mark point C at a position 481 mm (1.58 ft.) in front of point B.


v.

Mark point D at a position 2151 mm (7.06 ft.) in front of point B.


vi.

Using a string, mark line E at a position 1000 mm (3.28 ft.) from point C.


vii.

Using a string, mark line H at a position 1000 mm (3.28 ft.) from point C.


viii.

Using a string, mark line F at a position 1000 mm (3.28 ft.) from point D.


ix.

Using a string, mark line I at a position 1000 mm (3.28 ft.) from point D.


x.

Mark point G (placement point 2) at the point where line E and line F intersect.


xi.

Mark point J (placement point 3) at the point where line H and line I intersect.


xii.

Using tape and a string, create a line that connects point G and point J (target position line).

E336337C01
1.104,2.208 1.438,2.125 false 1.104,0.552 1.438,0.635 false 1.531,1.604 1.865,1.688 false 0.625,1.302 0.938,1.458 0.313,0.156 10 false *a 0.948,0.49 1.26,0.646 0.313,0.156 10 false *b 1.885,1.625 2.198,1.781 0.313,0.156 10 false *c 1.469,0.24 1.781,0.396 0.313,0.156 10 false *a 0.958,2.156 1.271,2.313 0.313,0.156 10 false *b 6.073,1.188 6.229,1.385 0.156,0.198 10 false A 2.458,1.198 2.615,1.396 0.156,0.198 10 false B 2.021,1.208 2.177,1.406 0.156,0.198 10 false C 1.417,1.208 1.573,1.406 0.156,0.198 10 false K 0.833,1.208 0.99,1.406 0.156,0.198 10 false D 1.417,0.76 1.573,0.958 0.156,0.198 10 false J 1.417,1.677 1.573,1.875 0.156,0.198 10 false G
*a String *b Tape
*c Target Position Line - -


HINT:
·

Make sure the string is taut when securing it with tape.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with points G and J.




xiii.

Mark point K (placement position 1) at the point the string connecting points C and D and the string connecting points G and J intersect.


xiv.

Confirm that the distance between points K and G (placement positions 1 and 2), and K and J (placement positions 1 and 3) is 550 mm (21.65 in.).

E336338C01
0.198,1.313 0.51,1.469 0.313,0.156 10 false *a 0.406,1.104 0.719,1.26 0.313,0.156 10 false *b 1.469,0.521 1.781,0.677 0.313,0.156 10 false *a 0.406,1.552 0.719,1.708 0.313,0.156 10 false *b 6.063,1.188 6.219,1.385 0.156,0.198 10 false A 2.458,1.188 2.615,1.385 0.156,0.198 10 false B 2.01,1.198 2.167,1.396 0.156,0.198 10 false C 0.813,1.188 0.969,1.385 0.156,0.198 10 false D 1.417,0.75 1.573,0.948 0.156,0.198 10 false J 1.417,1.198 1.573,1.396 0.156,0.198 10 false K 1.417,1.635 1.573,1.833 0.156,0.198 10 false G
*a String *b 550 mm (21.65 in.)


NOTICE:

If the distance between either pair of points is not within +/- 3 mm (0.118 in.) mm of the specified value, start over from the marking of point A.




d.

Perform Recognition Camera/Target Position Memory.

CAUTION:

Do not look into the forward recognition camera from a close distance.


NOTICE:
·

Close all of the doors.

·

Make sure that no one is inside the vehicle.

·

Do not lean on the vehicle.

·

Make sure that the headlights are turned off.



i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus:

Chassis > Front Recognition Camera > Utility
Tester Display
Recognition Camera/Target Position Memory
50005 386 2394

v.

According to the display on the GTS, press "Next". *1


vi.

Confirm the conditions displayed on the screen, and then press "Next".


vii.

Input "1288 mm (50.71 in.)" for the height of the recognition camera.


viii.

Input "7 mm (0.28 in.)" for the lateral position of the recognition camera, then press "Next".


ix.

Input "0 deg." for the yaw angle of the recognition camera.


x.

Input "-2.42 deg." for the pitch angle of the recognition camera, and then press "Next".


xi.

Input "1350 mm (53.15 in.)" for the height of the target.


xii.

Input "3000 mm (118.11 in.)" for the distance between the recognition camera and target, and then press "Next".


xiii.

Input "550 mm (21.65 in.)" for the distance between the targets.


xiv.

Input "180 mm (7.09 in.)" for the target size, and then press "Next".


xv.

Input "1761 mm (69.33 in.)" for the width of the vehicle.


xvi.

Input "735 mm (28.94 in.)" for the distance between the recognition camera and front tires, and then press "Next".


xvii.

Input "0 deg." for the pitch offset angle.


xviii.

Input "1625 mm (63.98 in.)" for the distance between the recognition camera and the radar, and then press "Next".


xix.

If "Recognition Camera/Target Position Memory has failed." is displayed on the GTS screen, confirm the conditions displayed on the screen, then press "Yes" and repeat the procedure from *1.


xx.

Press "Exit" to exit the Recognition Camera/Target Position Memory utility.



e.

Perform Recognition Camera Axis Adjust (target positioning).

NOTICE:
·

If "Recognition Camera Axis Adjust has failed." is displayed on the screen, confirm the following conditions, turn the power switch off and then to ON, and repeat the procedure from *1.

·

Make sure that the height of the target is correct.

·

Make sure that the target placement positions are correct.

·

Make sure that the orientation of the target sheet is correct (black area positioned at the top right).

·

Make sure that the surrounding area is sufficiently bright.

·

Make sure that there are no reflective or shiny objects around the target.

·

Make sure that there are no black and white patterned objects around the target or on a wall near the target.

·

Make sure that the shadow of the target is not cast onto a wall.

·

Make sure that the windshield glass is clean.



i.
E320106C01
0.76,3.094 1.052,3.177 false 1.542,2.854 1.646,3.073 false 1.552,2.771 1.99,2.823 true 1.01,1.479 1.333,1.542 false 2.021,2.76 2.333,2.917 0.313,0.156 10 false *b 1.635,3.094 1.948,3.25 0.313,0.156 10 false K 0.583,3.031 0.896,3.188 0.313,0.156 10 false *a 0.75,1.427 1.208,1.625 0.458,0.198 10 false SST
*a Target Position Line
*b Mark-off Line


Position SST so that it is aligned with the target position line and the mark-off line is aligned with point K (placement position 1) as shown in the illustration.

SST
09870-60000  (09870-60010, 09870-60020)


ii.

Enter the following menus:

Chassis > Front Recognition Camera > Utility
Tester Display
Recognition Camera Axis Adjust
50005 386 4409

iii.

According to the display on the GTS, press "Next". *1


iv.

Check that the values stored in the ECU are correct, and then press "Next".


v.

Confirm the conditions displayed on the screen, and then press "Next".


vi.

Select "Sequential recognition", and then press "Next".


vii.

Check that target is placed at point K (placement position 1), and then press "Next".


viii.
E320951C01
0.75,3.031 1.063,3.167 false 1.542,2.865 1.625,3.135 false 1.552,2.76 1.885,2.865 true 1.021,1.448 1.344,1.563 false 0.594,2.958 0.906,3.115 0.313,0.156 10 false *a 1.917,2.802 2.229,2.958 0.313,0.156 10 false *b 1.615,3.156 1.927,3.313 0.313,0.156 10 false G 0.75,1.385 1.208,1.583 0.458,0.198 10 false SST
*a Target Position Line
*b Mark-off Line


Position SST so that it is aligned with the target position line and the mark-off line is aligned with point G (placement position 2) as shown in the illustration.

SST
09870-60000  (09870-60010, 09870-60020)

NOTICE:

Position SST and press "Next" within 3 minutes of the screen changing to the Recognition Camera Axis Adjust screen for point G (placement position 2).



ix.
E320951C02
0.75,3.031 1.063,3.167 false 1.542,2.865 1.625,3.135 false 1.552,2.76 1.885,2.865 true 1.021,1.448 1.344,1.563 false 0.594,2.958 0.906,3.115 0.313,0.156 10 false *a 1.917,2.802 2.229,2.958 0.313,0.156 10 false *b 1.615,3.167 1.927,3.323 0.313,0.156 10 false J 0.75,1.385 1.208,1.583 0.458,0.198 10 false SST
*a Target Position Line
*b Mark-off Line


Position SST so that it is aligned with the target position line and the mark-off line is aligned with point J (placement position 3) as shown in the illustration.

SST
09870-60000  (09870-60010, 09870-60020)

NOTICE:

Position SST and press "Next" within 3 minutes of the screen changing to the Recognition Camera Axis Adjust screen for point J (placement position 3).



x.

If "Failed to read axis adjustment data" is displayed, perform Recognition Camera/Target Position Memory, and repeat the procedure from *1.


xi.

Press the "Exit" button to finish camera axis learning mode.


xii.

Turn the power switch off.


xiii.

Disconnect the GTS from the DLC3.