Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0244375 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B332383C04
0.719,0.146 1.031,0.344 0.313,0.198 10 false *a 2.479,0.146 2.792,0.344 0.313,0.198 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT BACK DOOR

a.

Check that the clearance measurements of areas a through l are within each standard range.

B435613N02
0.719,1.531 0.875,1.729 0.156,0.198 10 false a 1.135,1.844 1.292,2.042 0.156,0.198 10 false b 2.094,1.531 2.25,1.729 0.156,0.198 10 false c 2.552,1.844 2.708,2.042 0.156,0.198 10 false d 3.125,0.625 3.281,0.823 0.156,0.198 10 false e 3.552,0.406 3.708,0.604 0.156,0.198 10 false f 5.198,0.552 5.354,0.75 0.156,0.198 10 false g 6.563,1.021 6.719,1.219 0.156,0.198 10 false h 6.531,2.229 6.688,2.427 0.156,0.198 10 false i 6.5,3.802 6.646,4.042 0.146,0.24 10 false j 5.25,4.865 5.406,5.063 0.156,0.198 10 false k 3.979,5.01 4.135,5.208 0.156,0.198 10 false l

Standard Clearance
Area Measurement Area Measurement
a 4.6 to 9.6 mm (0.181 to 0.378 in.) b -0.5 to 4.5 mm (-0.0197 to 0.177 in.)
c 4.6 to 9.6 mm (0.181 to 0.378 in.) d -0.5 to 4.5 mm (-0.0197 to 0.177 in.)
e 4.6 to 9.6 mm (0.181 to 0.378 in.) f 1.0 to 6.0 mm (0.0394 to 0.236 in.)
g 3.85 to 7.85 mm (0.152 to 0.309 in.) h 3.5 to 8.5 mm (0.138 to 0.335 in.)
i 4.0 to 9.0 mm (0.157 to 0.354 in.) j 4.0 to 9.0 mm (0.157 to 0.354 in.)
k 5.0 to 10.0 mm (0.197 to 0.394 in.) l 4.35 to 8.35 mm (0.171 to 0.329 in.)


Hide 64718D 2.REMOVE DECK TRIM SERVICE HOLE COVER

a.
B435635C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws to remove the deck trim service hole cover as shown in the illustration.


Hide 3.ADJUST BACK DOOR

a.
B435634

Loosen the 4 hinge bolts on the back door and adjust the back door position.


b.

Tighten the 4 hinge bolts on the back door after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B435637

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 64718D 4.INSTALL DECK TRIM SERVICE HOLE COVER

a.
B435636C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the deck trim service hole cover as shown in the illustration.