Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM3210E _59 Vehicle Exterior _047506 MIRROR (EXT) _0244378 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319979C09
2.458,2.531 2.458,1.948 2.458,1.948 2.26,1.948 false 2.573,2.531 2.573,1.531 2.573,1.531 2.771,1.531 false 2.677,2.531 2.677,1.948 2.677,1.948 2.875,1.948 false 2.01,1.865 2.271,2.042 0.26,0.177 10 false MH 2.813,1.458 3.094,1.656 0.281,0.198 10 false M+ 2.927,1.875 3.208,2.156 0.281,0.281 10 false MV 1.354,2.24 1.521,2.385 0.167,0.146 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror heater.

i.
B319983C10
2.01,2.781 2.01,3.094 2.01,3.094 1.615,3.094 false 2.01,2.5 2.01,1.875 2.01,1.875 1.615,1.875 false 1.458,1.792 1.656,1.979 0.198,0.188 10 false + 1.5,3.031 1.771,3.25 0.271,0.219 10 false - 1.26,2.219 1.521,2.427 0.26,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 8 (-) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and the negative (-) auxiliary battery terminal to terminal 8, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B320731C11
0.969,3.115 0.802,3.115 0.802,3.115 0.802,2.781 false 1.052,1.74 0.802,1.74 0.802,1.74 0.802,2.573 false 2.688,0.042 2.938,0.281 0.25,0.24 10 false *a 1.99,2.292 2.458,2.625 0.469,0.333 10 false *e 2.406,2.063 2.771,2.458 0.365,0.396 10 false *d 2.865,1.792 3.156,2.073 0.292,0.281 10 false *c 3,0.917 3.281,1.208 0.281,0.292 10 false *b 1.125,1.677 1.438,1.885 0.313,0.208 10 false MR 1.042,3.042 1.417,3.25 0.375,0.208 10 false MF 0.25,0.24 0.563,0.5 0.313,0.26 10 false *f
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
((Outer Rear View Mirror Assembly RH))


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Auxiliary battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319980C09
1.49,2.521 1.49,1.844 1.49,1.844 1.75,1.844 false 1.385,2.521 1.385,1.615 1.385,1.615 1.167,1.615 false 1.281,2.521 1.281,1.896 1.281,1.896 1.063,1.896 false 1.802,1.76 2.125,1.969 0.323,0.208 10 false MV 0.948,1.542 1.229,1.729 0.281,0.188 10 false M+ 0.833,1.823 1.135,2.031 0.302,0.208 10 false MH 0.281,2.198 0.531,2.385 0.25,0.188 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns right
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror heater.

i.
B319984C12
0.854,2.563 0.854,1.969 0.854,1.969 1.094,1.969 false 0.865,2.823 0.865,3.208 0.865,3.208 1.104,3.208 false 1.188,3.135 1.333,3.313 0.146,0.177 10 false - 1.177,1.906 1.604,2.333 0.427,0.427 10 false + 0.292,2.271 0.583,2.479 0.292,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 8 (-) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and the negative (-) auxiliary battery terminal to terminal 8, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B320733C13
2.156,2.521 2.156,1.938 2.156,1.938 2.406,1.938 false 2.156,2.719 2.156,3.052 2.156,3.052 2.323,3.052 false 0.615,0.021 0.896,0.229 0.281,0.208 10 false *a 0.26,0.958 0.646,1.26 0.385,0.302 10 false *b 0.417,1.76 0.719,2.021 0.302,0.26 10 false *c 0.854,2.031 1.271,2.365 0.417,0.333 10 false *d 1.26,2.26 1.615,2.521 0.354,0.26 10 false *e 2.479,1.854 2.885,2.073 0.406,0.219 10 false MR 2.396,2.969 2.698,3.167 0.302,0.198 10 false MF 0.208,0.208 0.5,0.417 0.292,0.208 10 false *f
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Mirror Actuator Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Auxiliary battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.