Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM3210E _59 Vehicle Exterior _047506 MIRROR (EXT) _0244378 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 87966 1.INSTALL OUTER MIRROR RETRACTOR

a.
B436750N01
2.292,1.479 2.448,1.677 0.156,0.198 10 false 2 0.74,0.885 0.896,1.083 0.156,0.198 10 false 1

Install the 2 screws in the order shown in the illustration.


b.
B436753

Install a new frame sub-assembly to the housing with the 2 screws.


c.
B436752C01
0,0 0,0 false
V113147

Install in this Direction


Pass a new wire harness sub-assembly through the frame sub-assembly as shown in the illustration.


d.
B436749

Connect the connector.


e.
B436748

Engage the 2 clamps.


f.

Connect the connector.


g.
B436747

Install the actuator sub-assembly with the 3 screws.


h.
B436756

Wind vinyl tape around the wire harness sub-assembly to secure it.


i.

Pass the wire harness sub-assembly through the base sub-assembly.


j.

Remove the vinyl tape.


k.
B436746

Using a T25 "TORX" socket wrench, install the base sub-assembly with 3 new screws.

Torque:
3.1 N*m (32 kgf*cm, 27 in.*lbf)

NOTICE:

When installing the base sub-assembly, check that the wire harness sub-assembly is not caught between the base sub-assembly and body. Failure to do so may cause a short circuit.



l.
B436744

Engage the guide and 5 claws to install the lower cover.


m.
B442189

Pass the wire harness sub-assembly through a new gasket sub-assembly and engage the 3 guides to install the gasket sub-assembly.

NOTICE:

Make sure there is no clearance between the gasket sub-assembly and base sub-assembly.



n.
B436739C01
1.479,3.115 1.073,2.792 false 1.479,3.115 1.958,2.823 false 1.396,3.094 1.552,3.292 0.156,0.198 10 false *a
*a Marking


Adjust the wire harness sub-assembly so that the marking is at the position shown in the illustration.


o.
B436740N01
0.75,1.594 0.906,1.792 0.156,0.198 10 false A

Wind vinyl tape around the wire harness sub-assembly to secure it.

Reference Measurement
Area Measurement
A 50 mm (1.97 in.)

NOTICE:

If the vinyl tape is wrinkled, water may run down the wire harness sub-assembly and enter the vehicle. Make sure to wind the vinyl tape properly.



p.
B283920

Connect each connector to a new adapter.


q.
B283921C07
1.927,2.583 2.344,2.438 false 2.385,2.344 2.698,2.5 0.313,0.156 10 false *a
*a Wire Harness Routing


Route the longer part of the wire harness sub-assembly as shown in the illustration.


r.
B394558C02
0.979,0.729 1.396,0.313 false 2.094,1.844 2.25,2.042 0.156,0.198 10 false A 1.01,1.844 1.167,2.042 0.156,0.198 10 false B 1.417,0.198 1.729,0.396 0.313,0.198 10 false *a
*a Vinyl Tape


Wind vinyl tape around the wire harness sub-assembly to secure it.

Reference Measurement
Area Measurement
A 5.0 mm (0.197 in.)
B 50 mm (1.97 in.)


Hide 8794A 2.INSTALL NO. 2 OUTER MIRROR COVER

a.
B442199C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and 2 claws to install the No. 2 outer mirror cover as shown in the illustration.


Hide 81740 3.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY

Hide 87948 4.INSTALL OUTER MIRROR HOLE COVER

a.
B436745

Engage the guide and 5 claws to install the outer mirror hole cover.