Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS
RM3210E _59 Vehicle Exterior _047506 MIRROR (EXT) _0244379 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87931 1.INSPECT OUTER MIRROR RH

a.
B322114C03
1.792,0.885 1.792,0.552 1.792,0.552 2.458,0.552 false 1.875,1.104 2.375,1.104 false 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 2.531,0.49 2.688,0.688 0.156,0.198 10 false 1 2.448,1.042 2.604,1.24 0.156,0.198 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.



c.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
E338893C01
0,0 0,0 false
*a Component without harness connected
(Outer Mirror RH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.



Hide 87961 2.INSPECT OUTER MIRROR LH

a.
B322115C03
1.5,0.885 1.5,0.615 1.5,0.615 0.833,0.615 false 0.823,1.104 1.406,1.104 false 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.688,0.552 1,0.75 0.313,0.198 10 false 1 0.698,1.052 1.01,1.25 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the outer mirror heater operation. (w/ Mirror Heater)

i.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
E338894C01
0,0 0,0 false
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.