Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0244634 AIR CONDITIONING SYSTEM D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


Air conditioning system data and Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform troubleshooting.



LIST OF OPERATION METHODS


By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

E236715E83
4.604,5.083 5.052,5.344 0.448,0.26 2.979,5.083 3.635,5.344 0.656,0.26 1.354,4.198 1.802,4.458 0.448,0.26 1.344,5.625 1.792,5.885 0.448,0.26 0.5,7.75 0.948,8.01 0.448,0.26 3.885,5.083 4.385,5.344 0.5,0.26 2.24,6.438 2.833,6.698 0.594,0.26 3.073,6.448 3.521,6.708 0.448,0.26 1.563,0.385 4.24,1.229 2.677,0.844 10 false Turn the power switch on (IG) and press the air conditioning control assembly AUTO and recirculation/fresh switches simultaneously within 5 seconds. 4.615,1.208 6.635,1.792 2.021,0.583 10 false The AUTO and recirculation/fresh switches are not pressed simultaneously. 2.208,2.771 3.615,3.115 1.406,0.344 10 false Indicator Check (continuous operation) 2.104,4.167 3.813,4.51 1.708,0.344 10 false Sensor Check (DTC check) (continuous operation) 2.104,5.604 3.813,5.948 1.708,0.344 10 false Sensor Check (DTC check) (step operation) 4.646,5.125 5.052,5.281 0.406,0.156 10 false AUTO 3.042,5.125 3.646,5.365 0.604,0.24 10 false UP Dr*A 1.458,7.188 4.427,7.344 2.969,0.156 10 false Check mode is canceled and A/C control starts 1.458,4.25 1.865,4.406 0.406,0.156 10 false OFF 1.458,5.677 1.865,5.833 0.406,0.156 10 false OFF 1,7.792 2.708,7.948 1.708,0.156 10 false : Indicates switch operation 0.719,8.146 2.365,8.302 1.646,0.156 10 false OFF: Blower fan off switch 3.104,8.156 5.656,8.313 2.552,0.156 10 false UP Dr: Driver side temperature up switch 3.104,7.813 5.656,7.969 2.552,0.156 10 false AUTO: Automatic air conditioning switch 3.969,5.125 4.375,5.281 0.406,0.156 10 false UP*B 3.698,5.125 4.104,5.281 0.406,0.156 10 false or 2.271,6.479 2.865,6.729 0.594,0.25 10 false UP Dr*A 3.125,6.49 3.531,6.646 0.406,0.156 10 false UP*B 2.896,6.49 3.302,6.646 0.406,0.156 10 false or 0.729,8.479 2.625,8.698 1.896,0.219 10 false UP: Temperature up switch 3.031,8.49 4.927,8.708 1.896,0.219 10 false *A: for Dual Type 4.646,8.49 6.542,8.708 1.896,0.219 10 false *B: for Single Type


INDICATOR CHECK


a.

Turn the power switch off.


b.

Turn the power switch on (IG) and press the air conditioning control assembly AUTO and recirculation/fresh switches simultaneously within 5 seconds.

E338807C01
0.198,0.188 0.573,0.427 0.375,0.24 12 false *A 3.865,0.198 4.24,0.438 0.375,0.24 12 false *B 0.198,2 0.573,2.24 0.375,0.24 12 false *C 3.885,2.083 4.26,2.323 0.375,0.24 12 false *D
*A for LHD (for Dual Type) *B for RHD (for Dual Type)
*C for LHD (for Single Type) *D for RHD (for Single Type)



c.

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

E338808C01
0.188,0.26 0.563,0.5 0.375,0.24 12 false *A 3.51,0.271 3.885,0.51 0.375,0.24 12 false *B 0.188,1.896 0.563,2.135 0.375,0.24 12 false *C 3.521,1.885 3.896,2.125 0.375,0.24 12 false *D 2.25,3.417 2.625,3.656 0.375,0.24 10 false *a 2.833,3.594 3.208,3.833 0.375,0.24 10 false *d 3.438,3.594 3.813,3.833 0.375,0.24 10 false *d 2.5,3.927 2.875,4.167 0.375,0.24 10 false *b 2.51,4.438 2.885,4.677 0.375,0.24 10 false *c
*A for LHD (for Dual Type) *B for RHD (for Dual Type)
*C for LHD (for Single Type) *D for RHD (for Single Type)
*a Indicator Blinking Pattern *b ON
*c OFF *d 1 Sec.


HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the OFF switch to cancel check mode.





SENSOR CHECK (DTC CHECK)


a.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



b.

Read the DTCs displayed on the display.

E338809C01
1.188,1.042 1.396,0.625 1.396,0.625 1.542,0.625 false 5.927,1.052 6.135,0.635 6.135,0.635 6.281,0.635 false 1.229,2.615 1.438,2.198 1.438,2.198 1.583,2.198 false 5.844,2.635 6.052,2.219 6.052,2.219 6.198,2.219 false 0.177,0.531 0.552,0.771 0.375,0.24 12 false *A 3.583,0.583 3.958,0.823 0.375,0.24 12 false *B 0.167,2.115 0.542,2.354 0.375,0.24 12 false *C 3.615,2.146 3.99,2.385 0.375,0.24 12 false *D 1.583,0.51 1.958,0.75 0.375,0.24 10 false *a 6.302,0.521 6.677,0.76 0.375,0.24 10 false *a 1.615,2.094 1.99,2.333 0.375,0.24 10 false *a 6.229,2.104 6.604,2.344 0.375,0.24 10 false *a
*A for LHD (for Dual Type) *B for RHD (for Dual Type)
*C for LHD (for Single Type) *D for RHD (for Single Type)
*a Diagnostic Trouble Code (DTC) - -


NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that DTC 12 is output.




c.

If the DTCs are difficult to read because they change automatically, Push the driver side TEMP up switch*1 or TEMP up switch*2 to display the steps one at a time so that they can be read easily. The items are displayed step by step each time the driver side TEMP up switch*1 or TEMP up switch*2 is pushed.

*1: for Dual Type

*2: for Single Type


E338810C01
0.198,0.5 0.573,0.74 0.375,0.24 12 false *A 3.667,0.51 4.042,0.75 0.375,0.24 12 false *B 0.229,2.146 0.604,2.385 0.375,0.24 12 false *C 3.74,2.146 4.115,2.385 0.375,0.24 12 false *D
*A for LHD (for Dual Type) *B for RHD (for Dual Type)
*C for LHD (for Single Type) *D for RHD (for Single Type)


HINT:

Press the OFF switch to finish panel diagnosis.



d.

Clear the DTCs.

i.

During the sensor check, press the front defroster switch and rear defogger switch simultaneously.

E338811C01
0.427,0.552 0.802,0.792 0.375,0.24 12 false *A 3.99,0.583 4.365,0.823 0.375,0.24 12 false *B
*A for LHD *B for RHD