DESCRIPTION
The certification ECU (smart key ECU assembly) and hybrid vehicle control ECU control the vehicle immobiliser system functions. Immobiliser system data and Diagnostic Trouble Codes (DTCs) can be read through the vehicle Data Link Connector 3 (DLC3).
In some cases, a malfunction may be occurring in the immobiliser system even though the security indicator light is not illuminated.
When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform repairs.
CHECK DLC3
Check the DLC3.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION
INSPECT AUXILIARY BATTERY VOLTAGE
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery.
START FUNCTION PROBLEM SYMPTOMS
| Symptom | Suspected Area | Component Malfunction | Possible Output DTCs | Related Data List Item |
|---|---|---|---|---|
| Hybrid control system cannot be started*1 | Certification ECU (smart key ECU assembly) | Open or short circuit inside ECU | ·
B278A ·
B279986 ·
B279A12 |
·
# Codes ·
Immobilizer when IG=ON ·
Immobiliser ·
Master Key ·
Sub Key ·
BCC Malfunction ·
Abnormal Status ·
Different Encrypt Code ·
Different Serial Number ·
Frame Error ·
Response ·
Wireless Starter Com ID ·
Wireless C Code ·
Engine Start Condition ·
ID-BOX Sleep Condition ·
ID-BOX Start Condition ·
Engine Start Request ·
3bit Code Request ·
S Code Check ·
L Code Check ·
Unlock Request Receive ·
Lock Request Receive ·
S Code Check (Past) ·
L Code Check (Past) ·
EFI Code Receive ·
EFI Communication |
| Hybrid control system cannot be started*1 | ID code box (immobiliser code ECU) | Open or short circuit inside ECU | ·
B2790 ·
B279986 ·
B279A12 |
·
Immobilizer when IG=ON ·
Immobiliser ·
Master Key ·
Sub Key ·
BCC Malfunction ·
Abnormal Status ·
Different Encrypt Code ·
Different Serial Number ·
Frame Error ·
Response ·
ID-BOX Sleep Condition ·
ID-BOX Start Condition ·
Engine Start Request ·
3bit Code Request ·
S Code Check ·
L Code Check ·
S Code Check (Past) ·
L Code Check (Past) ·
EFI Code Receive ·
EFI Communication |
| Hybrid vehicle control ECU | Open or short circuit inside ECU | ·
B279986 ·
B279A12 ·
B279C95 |
EFI Code Receive | |
| Hybrid control | Hybrid vehicle control ECU incompatible with installed immobiliser system | B279C95 | ·
Engine Start Condition ·
EFI Code Receive |
|
| Power source mode cannot be changed*1 | Power switch | Open or short circuit inside switch | B278A | ·
Unlock Request Receive ·
Lock Request Receive |
| Certification ECU (smart key ECU assembly) | Open or short circuit inside ECU | ·
B2271 ·
B2274 |
·
Immobilizer when IG=ON ·
Immobiliser |
|
| Gearshift control lock/unlock not possible*2 | Hybrid vehicle control ECU | ·
Open or short circuit inside ECU ·
Actuator stuck |
·
B2781 ·
B2782 ·
B2788 |
·
Unlock Request Receive ·
Lock Request Receive |
*1: Refer to Problem Symptoms Table for Entry and Start System (for Start Function).
*2: Refer to Problem Symptoms Table for Electronic Shift Lever System.
Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>PROBLEM SYMPTOMS TABLE